SDS

MATERIAL SAFETY DATA SHEET
The information contained herein is based on data available at the time of preparation of this data sheet which Akzo Nobel Paints believes to be reliable. However, no warranty is expressed or implied regarding the accuracy
of this data. Akzo Nobel Paints shall not be responsible for the use of this information, or of any product, method or apparatus mentioned and you must make your own determination of its suitability and completeness for
your own use, for the protection of the environment, and the health and safety of your employees and the users of this material.
Complies with OSHA hazard communication standard 29CFR1910.1200.
prepared 04/27/11
GLIDDEN OIL GLOSS TRIM AND DOOR PAINT
GL3XX
Akzo NobeI Paints 15885 Sprague Road Strongsville, Ohio 44136 EMERGENCY TELEPHONE NO. [phone]
HAZARDS IDENTIFICATION (ANSI Section 3)
Primary route(s) of exposure : Inhalation, skin contact, eye contact, ingestion.
Effects of overexposure :
Inhalation : Irritation of respiratory tract. Prolonged inhalation may lead to loss of appetite, mucous
membrane irritation, drowsiness, dizziness and/or lightheadedness, headache, uncoordination,
nausea, vomiting, coughing, central nervous system depression, intoxication, difficulty of
breathing, allergic response, severe lung irritation or damage, liver damage, kidney damage,
convulsions, loss of consciousness, asphyxiation. Possible sensitization to respiratory tract.
Skin contact : Irritation of skin. Prolonged or repeated contact can cause dermatitis, defatting. Skin
contact may result in dermal absorption of component(s) of this product which may cause
drowsiness, dizziness and/or lightheadedness, central nervous system depression.
Eye contact : Irritation of eyes. Prolonged or repeated contact can cause conjunctivitis, corneal injury.
Ingestion : Ingestion may cause lung inflammation and damage due to aspiration of material into
lungs, mouth and throat irritation, mucous membrane irritation, drowsiness, dizziness and/or
lightheadedness, headache, uncoordination, nausea, vomiting, diarrhea, gastro-intestinal
disturbances, central nervous system depression, difficulty of breathing, liver damage, kidney
damage, convulsions, loss of consciousness.
Medical conditions aggravated by exposure : Eye, skin, respiratory disorders, asthma-like
conditions.
FIRST-AID MEASURES (ANSI Section 4)
Inhalation : Remove to fresh air. Restore and support continued breathing. Get emergency medical
attention. Have trained person give oxygen if necessary. Get medical help for any breathing
difficulty. Remove to fresh air if inhalation causes eye watering, headaches, dizziness, or other
discomfort.
Skin contact : Wash thoroughly with soap and water. If any product remains, gently rub petroleum
jelly, vegetable or mineral/baby oil onto skin. Repeated applications may be needed. Remove
contaminated clothing. Wash contaminated clothing before re-use.
Eye contact : Flush immediately with large amounts of water, especially under lids for at least 15
minutes. If irritation or other effects persist, obtain medical treatment.
Ingestion : If swallowed, obtain medical treatment immediately.
FIRE-FIGHTING MEASURES (ANSI Section 5)
Fire extinguishing media : Dry chemical or foam water fog. Carbon dioxide. Closed containers may
explode when exposed to extreme heat or fire. Vapors are heavier than air and may travel long
distances to a source of ignition and flash back. Vapors can form explosive mixtures in air at elevated
temperatures. May decompose under fire conditions emitting irritant and/or toxic gases.
Fire fighting procedures : Water may be used to cool and protect exposed containers. Firefighters
should use full protective clothing, eye protection, and self-contained breathing apparatus.
Hazardous decomposition or combustion products : Carbon monoxide, carbon dioxide, oxides of
nitrogen, oxides of sulfur, toxic gases, acrylic monomers.
ACCIDENTAL RELEASE MEASURES (ANSI Section 6)
Steps to be taken in case material is released or spilled : Comply with all applicable health and
environmental regulations. Eliminate all sources of ignition. Ventilate area. Use non-sparking tools.
Evacuate all unnecessary personnel. Place collected material in proper container. Spilled material is
extremely slippery. Complete personal protective equipment must be used during cleanup. Large
spills - shut off leak if safe to do so. Dike and contain spill. Pump to storage or salvage vessels. Use
absorbent to pick up excess residue. Keep salvageable material and rinse water out of sewers and
water courses. Small spills - use absorbent to pick up residue and dispose of properly.
HANDLING AND STORAGE (ANSI Section 7)
Handling and storage : Store below 100f (38c). Keep away from heat, sparks and open flame.
Other precautions : Use only with adequate ventilation. Do not take internally. Keep out of reach of
children. Avoid contact with skin and eyes, and breathing of vapors. Wash hands thoroughly after
handling, especially before eating or smoking. Keep containers tightly closed and upright when not
in use. Avoid conditions which result in formation of inhalable particles such as spraying or abrading
(sanding) painted surfaces. If such conditions cannot be avoided, use appropriate respiratory
protection as directed under exposure controls/personal protection. Empty containers may contain
hazardous residues. Ground equipment when transferring to prevent accumulation of static charge.
EXPOSURE CONTROLS/PERSONAL PROTECTION (ANSI Section 8)
Respiratory protection : Control environmental concentrations below applicable exposure standards
when using this material. When respiratory protection is determined to be necessary, use a
NIOSH/MSHA (Canadian z94.4) Approved elastomeric sealing- surface facepiece respirator
outfitted with organic vapor cartridges and paint spray (dust/mist) prefilters. Determine the proper
level of protection by conducting appropriate air monitoring. Consult 29CFR1910.134 For selection
of respirators (Canadian z94.4).
Ventilation : Provide dilution ventilation or local exhaust to prevent build-up of vapors. Use explosion-
proof equipment.
Personal protective equipment : Eye wash, safety shower, safety glasses or goggles. Impervious
gloves, impervious clothing.
STABILITY AND REACTIVITY (ANSI Section 10)
Under normal conditions : Stable can form explosive peroxides on long standing in air. See section 5
fire fighting measures
Materials to avoid : Oxidizers, acids, reducing agents, bases, halogens, mineral acids. Nitrates.
Conditions to avoid : Elevated temperatures, contact with oxidizing agent, sparks, open flame, ignition
sources.
Hazardous polymerization : Will not occur
TOXICOLOGICAL INFORMATION (ANSI Section 11)
Supplemental health information : Contains a chemical that may be absorbed through skin. Notice -
reports have associated repeated and prolonged occupational overexposure to solvents with
permanent brain and nervous system damage. Intentional misuse by deliberately concentrating
and inhaling the contents may be harmful or fatal. Contains iron oxide, repeated or prolonged
exposure to iron oxide dust may cause siderosis, a benign pneumoconiosis. Other effects of
overexposure may include toxicity to liver, kidney, lungs.