glitz home’ Glitz home Corporation (Shanghai), Ltd. Assembly Instruction 4 SHELF BOOKCASE a [1] VB-VS £ Carefully unpack and Identify each component before beginning assembly. Before you begin, please refer to pairs list to make sure that you have all parts. Please take care when assembling the unit and always place the parts on a clean, soft surface.
glitz home’ atm CAUTION: Assembly will require at least 2 adults. DO NOT use power tools. Please inspect all items BEFORE assembly. If for any reason you need to return this item, please kindly rectum it in it's original packaging. © WARNING! 1. DO NOT let any sharp objects touch or rub the surface of the product. 2. When assembling, do not let children play around the working area. 3. DO NOT tighten all bolts and screws completely until the entire unit has been assembled and set up. 4.
glitz home’ SHELF PANEL (A) TOP PANEL (B) SHELF CROSS BAR (C) | REAR CROSS BAR (D) Qty: 3 Qty: 1 Qty: 4 Qty: 4 LEFT UPPER FRAME (E) | LEFT BOTTOM PANEL RIGHT UPPER FRAME RIGHT BOTTOM FRAME F) © (H) Qty: 1 Qty: 1 Qty: 1 Qty: 1 HARDWARE LIST ALLEN BOLT (1) ALLEN BOLT (2) ALLEN BOLT (3) ALLEN BOLT (4) M6*12mm M6*22mm M6*28mm M5*15mm Qty: 9 Qty: 8 Qty: 1 PHILLIPS SCREW (5) NUT (6) ALLEN WRENCH (7) OPEN END WRENCH (8) 4*12mm M5 4mm Qty: 4 Qty: 1 Qty: 1 Qty: 1 L STEEL PLATE (9) ANTI-TIPPING STRIP (10)| WALL ANCHO
glitz home’ REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION SKETCH QTY 1 ALLEN BOLT M6*12mm »& PCS STEP 1 7 ALLEN WRENCH Ss 1PC Assemble left upper frame (E) on left bottom frame (F) with Allen bolts (1) by using Allen wrench (7). Repeat this action for Tess 4 holes must be one side Tess 4 holes must be one side REQUIRED HARDWARE IN THIS STEP NO.
glitz home’ STEP 3 REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION SKETCH QTY 4 ALLEN BOLT M5*15MM H 1PC 6 NUT MS @ 1PC 7 ALLEN WRENCH SS 1PC 8 OPEN END WRENCH = 1PC Assemble all rear cross bars (F) together at one end with Allen bolts (4) and nut (6) using Allen wrench (7)and Open end wrench (8). Fully tighten in this step. STEP REQUIRED HARDWARE IN THIS STEP NO.
glitz home’ REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION SKETCH QTY 3 ALLEN BOLT M6*28MM PCS STEP 5 7 ALLEN WRENCH ss 1PC Assemble top panel (B) & shelf panel (A) on ready metal frame with Allen bolts (3) by using Allen wrench (7). B The hole on top panel (B) N\ should be on the bottom A and same side as x steel 3 A wire (F). REQUIRED HARDWARE IN THIS STEP NO.
glitz home’ REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION SKETCH QTY 9 STEEL PLATE © 1PC 10 ANTI-TIPPING STRIP a 1PC 1 WALL ANCHOR e= 1PC STEP 7 12 SCREW M4*25MM a) 1PC Drill one hole on the wall and then put wall anchor (11) into the per-drilled hole. Assemble steel plate (9) to the wall with screw (12) using screwdriver. Attach anti-tipping strip (10) to the steel plate (9) as shown.