User's Manual

ManualsBrandsGlobal Display Solutions ManualsElectronicsMifare/NFC reader

This document and information herein is the property of Global Display Solutions and all unauthorised use and

Unpublished Property of GDS.

MAN10408_00 1 of 8

MAN10454 Rev.00

Description

User Manual - NFC 12V board

GDS Part No.

BRD01793 - 0WQ00484AC

Issue Date

19.07.2013

Issue Level

Pages

Author(s):

Signature:

Date:

F.Ceccato

19/07/2013

Approved:

P. Giardini

P.Giardini

19/07/2013

Final Release

This technical literature is subject to change without notice.

Please contact GDS or its representative before designing your product based on this specification

Summary of content (8 pages)

PAGE 1
MAN10454 Rev.00 Description User Manual - NFC 12V board GDS Part No. BRD01793 - 0WQ00484AC Issue Date 19.07.2013 Issue Level 00 Pages 7 Author(s): Signature: Date: F.Ceccato F.Ceccato 19/07/2013 P.Giardini 19/07/2013 Approved: P. Giardini Final Release This technical literature is subject to change without notice.
PAGE 2
1. 2. 3. 4. 5. 6. 7. TABLE OF CONTENTS FCC Notice (U.S. Only) ............................................................................................. 3 Safety Instructions ..................................................................................................... 4 NFC compatibility ...................................................................................................... 4 Mechanical dimensions ....................................................................................
PAGE 3
1. FCC Notice (U.S. Only) FCC Class B This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules.
PAGE 4
2. Safety Instructions The NFC 12V board is a Mifare/NFC reader module of the Technogym Devices Technogym Device (Equipment Cardio, Trainer point or Class Reader). Read the Safety Instruction carefully and keep it for use later. Beware of all warning and instruction signs marked on the NFC 12V board. Ensure that the ambient temperature around the module is between +5°C and +50 °C (with relative humidity between 5% and 85%). 3.
PAGE 5
4. Mechanical dimensions The NFC 12V board shows the following mechanical dimensions: Quote MAX Dimension PBC_W 86mm PCB_L 51mm PCB_H Ant_W 1.6mm 56 mm Ant_L 40mm The electronic board has all components on one side only and the connectors must be of type SMT. Figure 1 NFC 12V board mechanical dimensions This document and information herein is the property of Global Display Solutions and all unauthorised use and reproduction is prohibited. Copyright © 2012 by Global Display Solutions, Italy.
PAGE 6
5. Connections The NFC 12V board has the main connector (Picoblade Molex SMT - 53398-087) with reference J9. Pin 1 2 3 4 5 6 7 8 Function +12Vdc RS232_TX RS232_RX RTS out CTS in Relè out NC GND Description Power Supply Serial Data Out Serial Data In RTS out CTS in Relè out NC Ground Figure 2 J9 connector details The J2 connection (Picoblade Molex SMT - 53398-0471) is used to connect e the optional Remote Mifare Board with this pinout: Pin 1 2 3 4 Function +3.
PAGE 7
Figure 4 NFC 12V board state diagram with and without equipment connected This document and information herein is the property of Global Display Solutions and all unauthorised use and reproduction is prohibited. Copyright © 2012 by Global Display Solutions, Italy. All rights reserved. Confidential, Unpublished Property of GDS.
PAGE 8
7. Labelling The NFC 12V board has labeling showing FCC ID code, GDS SpA board code and Technogym SpA codes.