Installation Guide

ManualsBrandsGlobal Door Controls ManualsKitchenSingle Cylinder Brushed Chrome Commercial Deadbolt

a. Fold and apply template on

high edge of door bevel and

mark center of door edge as

indicated on template at the

desired height from the floor.

b. Mark center hole on door face

through guide on template for

either 2-3/8" or 2-3/4" (60mm

or 70mm) backset.

NOTE: BACKSET ON DOOR

FACE MUST BE SAME

AS BACKSET OF YOUR

LOCK.

screw holes on

strike with center

lines on jamb.

Mark outline and

chisel 5/64" (2mm)

deep for strike.

Measure one half

of door thickness

from door stop and

mark vertical center

line of strike. Drill 1"

(25mm) hole 1" (25

mm) deep at inter-

section of horizontal

and vertical center

line of strike. Match

INSTRUCTIONS FOR INSTALLATION OF SINGLE

OR DOUBLE CYLINDER DEADBOLTS AND THE

REPLACEMENT OF EXISTING LOCKS

1. MARK DOOR

4. INSTALL STRIKE

Install strike and

tighten screws.

2. DRILL HOLES

3. INSTALL LATCH

Insert latch and

tighten screws.

Chisel 1/8" (3mm)

deep or until face

plate flush with

door edge.

Insert latch in hole.

Mark outline of

face plate and

remove latch.

Drill holes as marked.

NOTE:

DRILL 2-1/8" (54mm)

HOLE FROM BOTH

SIDES OF DOOR TO AVOID

SPLITTING WOOD.

Close door to mark

horizontal center

line of strike.

5. INSTALL SINGLE CYLINDER

6. INSTALL DOUBLE CYLINDER

EXTERIOR CYLINDER

LATCH

CRANK

KEY HOLE

EXTERIOR TAIL PIECE

EXTERIOR CYLINDER

LATCH CRANK

INTERIOR TAIL PIECE

EXTERIOR TAIL PIECE

EXTERIOR

CYLINDER

INSTALLATION SCREW

INTERIOR CYLINDER

2-1/8" (54mm) HOLE

FOR LOCKSET

1" (25mm)

FOR DEADBOLT

INSTALLATION

SCREW

INSIDE TURN UNIT

EXTERIOR CYLINDER

a. Retract deadbolt to unlock

position.

b. Insert exterior tail piece

horizontally through latch

crank.

c. Press exterior cylinder

flush against door.

d. Install inside turn unit and

tighten installation screws.

a. Retract deadbolt to unlock

position.

b. Insert exterior tail piece

horizontally through latch

crank.

c. Press exterior cylinder

flush against door.

d. Insert interior tail piece

vertically through latch

crank.

e. Press interior cylinder

flush against door and

tighten installation

screws.

KEY HOLE

FOR USE ON DOOR THICK 1-3/8" TO 1-3/4"

(35mm-45mm)

TOOLS REQUIRED FOR NEW CONSTRUCTION:

1 philips head screwdriver

1 2-1/8" (54mm) hole saw

1 1" (25mm) drill & 1 chisel

TOOLS REQUIRED FOR REPLACEMENT:

1 philips head screwdriver

LA3

LA3 LA3

1-3/8" (35mm)

THICK DOOR

FOLD HERE

2-3/8"

(60mm)

DRILL1" HOLE IN EDGE

OF DOOR (2" IN DEPTH)

DRILL (2-1/8")

54mm HOLE

MARK

PROPER

DOOR

THICKNESS

READ INSTRUCTIONS

1-3/4" (45mm) THICK DOOR

2-3/4"

(70mm)

MARK

FOR INSTALLING

DEADLOCKS

NOTE:

TEMPLATE MUST BE

PLACED ON HIGH

EDGE OF DOOR BEVEL

Summary of content (2 pages)

PAGE 1
LA3 LA3 INSTRUCTIONS FOR INSTALLATION OF SINGLE OR DOUBLE CYLINDER DEADBOLTS AND THE REPLACEMENT OF EXISTING LOCKS 1. MARK DOOR FOR USE ON DOOR THICK 1-3/8" TO 1-3/4" (35mm-45mm) TOOLS REQUIRED FOR NEW CONSTRUCTION: 1 philips head screwdriver 1 2-1/8" (54mm) hole saw 1 1" (25mm) drill & 1 chisel TOOLS REQUIRED FOR REPLACEMENT: 1 philips head screwdriver 5. INSTALL SINGLE CYLINDER a.
PAGE 2
LA3 INSTRUCTIONS D'INSTALLATION DE ' ^ PENES DORMANTS A CYLINDRE SIMPLE OU DOUBLE ET DE REMPLACEMENT DE SERRURES 1. MARQUER LA PORTE LA3 POUR INSTALLATION SUR PORTES DE ' ' ' 1-3/8 PO A 1-3/4 PO (35mm A 45mm) D'EPAISSEUR OUTILS REQUIS POUR UNE CONSTRUCTION NEUVE: 1 toumevis cruclforme 1 scle cloche 2-1/8 po (54mm) ' 1 meche de 1 po (25mm) et un ciseau a' bois OUTILS REQUIS POUR UN REMPLACEMENT: 1 tournevls cruciforme 5. INSTALLER LE CYLINDRE SIMPLE a.