User Manual

ManualsBrandsGlobal Industrial ManualsDrinking Fountains & CoolersGlobal Industrial Outdoor Drinking Fountain w/ Bottle Filling Station, Green

globalindustrial.ca

Distribucion Industrial Globales S DE RL DE CF

Instruction Manual Manual de Instrucciones Manuel d'instruction

Customer Service

US: 1-800-645-2986

Servicio de atención al Cliente

México: 01.800.681.6940

Service à la clientèle

Canada: 888-645-2986

Outdoor Drinking Fountain w/ Bottle Filling Station

Models 761216, 761216BK,

761216BL & 761216GN

• All installation work must be performed by authorized

service personnel.

• Two or more people are recommended to lift and

install the unit.

• To avoid the risk of property damage and/or personal

injury, ensure the mounting surface is adequate to support

400 lbs.

• Check local codes for plumbing requirements prior

to installation.

• Refer to Rough-In Guide (page 4) prior to installation.

• Thoroughly flush all water supply lines of all foreign

matter before connecting to the fixture.

• Check for any leaks before use.

• DO NOT attempt to repair or replace any part of this

fountain unless it is specifically recommended in this

manual. All other services should be referred to a

qualified technician.

• For use with clean, clear potable drinking water only.

• Shut-off water supply during installation to reduce the

risk of water damage.

• Freezing Caution: Before freezing temperatures occur,

refer to the Draining and Winterization section of this

manual (page 11) for proper preparation.

• Installation of a trap on the water drain line may be

necessary; remove trap before winterization draining.

• Failure to follow safety warnings and/or

installation instructions will void warranty.

WARNING

Note: This unit is designed to be installed on the surface of an existing or new concrete slab.

Included are the necessary vandal-resistant stainless steel bolts and washers needed

to anchor this unit. Installer must provide a 1-1/2” PVC drain line (if applicable) and water supply

line. All connections are made inside the item through the access doors, as shown in the drawings.

It is recommended to install a shut-off valve (not included) on the water supply.

Summary of content (11 pages)

PAGE 1
globalindustrial.ca Instruction Manual Customer Service US: 1-800-645-2986 Distribucion Industrial Globales S DE RL DE CF Manual de Instrucciones Servicio de atención al Cliente México: 01.800.681.6940 Manuel d'instruction Service à la clientèle Canada: 888-645-2986 Outdoor Drinking Fountain w/ Bottle Filling Station WARNING Models 761216, 761216BK, 761216BL & 761216GN • All installation work must be performed by authorized service personnel.
PAGE 2
Outdoor Drinking Fountain w/ Bottle Filler Instruction Manual BOTTLE FILLER SPOUT DRAIN PAN PEDESTAL PEDESTAL ARM BUBBLER DRAIN PUSH BUTTON DRINKING FOUNTAIN BASE COLOR OPTIONS: SS316 SS316 GREEN SS316 BLACK SS316 BLUE WWW.GLOBALINDUSTRIAL.
PAGE 3
Outdoor Drinking Fountain w/ Bottle Filler SPECIFICATIONS Features: Finish: Power: Bubbler Activation Type: Mounting Type: Product Dimensions: Weight: Installation Location: No. of Stations: 316 Stainless, Laminar Flow, Heavy Duty, Vandal Resistant SS Finish, Black(BK), Blue(BL), Green(GN) No Electrical Required Vandal Resistant Push Button Floor Mount/Free Standing 30.8"L x 14.4"W x 60.3"H 103 lbs. Outdoor 2 PART BREAKDOWN Ref. Qty. Descrip�on Ref. Qty.
PAGE 4
14'' 355mm 8 1/4'' 210mm INSIDE OPENING 1-1/2 '' WASTE 14'' 355mm 11 1/2'' 300mm A = 3/8” O.D. UNPLATED COPPER TUBE CONNECT - SHUT-OFF VALVE BY OTHERS B = ACESS PANEL (7” X 20”) B-2 = ACCESS PANEL (7” X 7”) C = REMOVABLE BOTTOM COVER LEGEND: 9'' 225mm 11 1/2'' 300mm 8 1/4'' 210mm INSIDE OPENING 29'' 753mm 40'' 1023mm 16'' 376mm 1.
PAGE 5
Outdoor Drinking Fountain w/ Bottle Filler Instruction Manual INSTALLATION • It is recommended that 2 or more people install this unit. • This fountain must be mounted on a solid, flat surface with adequate strength (concrete pad recommended) capable of supporting 400 lbs. • Locate and install plumbing through ground as required. Refer to Rough-In Guide (page 4) for proper location and correct plumbing. • Install a drainable shut-off valve (not included) if in a freezable environment.
PAGE 6
Outdoor Drinking Fountain w/ Bottle Filler Instruction Manual 2. INSTALL BUBBLER 2a. Unscrew and remove nut and washers from Bubbler (P1). 2b. Locate the hole on the drinking fountain pan surface. Align and sandwich with the two washers and tighten the nut to secure the bubbler. 2c. Bubbler is now properly installed. 3. MOUNT PEDESTAL TO GROUND • Locate and install plumbing through ground as required. Refer to Rough-In Guide (page 4) for proper location and correct plumbing.
PAGE 7
Instruction Manual Outdoor Drinking Fountain w/ Bottle Filler 5. CONNECT WATER INLET LINES • Install a shut-off valve (not included) on the water supply. • All water connections and drains must comply with local codes.
PAGE 8
Instruction Manual Outdoor Drinking Fountain w/ Bottle Filler WATER INLET LINE CONNECTION BREAKDOWN: FRONT VIEW SIDE VIEW P2 P5 (39-1/2”) P3 P5 (25-1/2”) P5 (25-1/2”) P3 P5 (6-1/4”) P6 (31-1/2”) P4 Install Shut-off Valve (Not Included) WATER SOURCE P4: Straight Flow Check Valve: All Water Inlet Connec�ons: OPERATION OF QUICK CONNECT FITTINGS 3/8” O.D. TUBE CONNECT COLD WATER SUPPLY SIMPLY PUSHIN IN SIMPLY PUSH TUBE TO TUBE TOATTACH ATTACH A A NOTE: WATERFLOW DIRECTION FIG. 1 FIG.
PAGE 9
Outdoor Drinking Fountain w/ Bottle Filler Instruction Manual CONNECT WATER DRAIN LINES • All water connections and drains must comply with local codes. • Through the rear access windows, connect water drain lines as illustrated below. NOTE: All drain lines attach with quick connect connections. • Installation of a trap on the water drain line may be necessary; check local codes.
PAGE 10
Instruction Manual Outdoor Drinking Fountain w/ Bottle Filler WATER DRAIN LINE CONNECTION BREAKDOWN: FRONT VIEW SIDE VIEW P8 P12 P11 (16-3/4”) P10 P11 (28-1/8”) Confirm with local codes for trap and other drainage requirements Note: Turn on water supply and check all connections for leaks and proper operation. Reinstall all (4) access panels using the (24) M6 x 10 flat-head anti-theft screws preciously removed from the fountain. WARNING: Flush all water supply lines thoroughly before initial use.
PAGE 11
Outdoor Drinking Fountain w/ Bottle Filler Instruction Manual START-UP Initial water flow may have sputter due to air in the water lines; this will be eliminated once air is purged from all water lines. Press and hold the push button until a steady water stream is achieved. STREAM HEIGHT ADJUSTMENT To adjust the water stream height, insert a small flathead screwdriver through the access hole in the center of the push button and turn the adjustment screw.