CORDLESS DRILL 443T, 243T, 183T, GTX12100K, GTX144100K INSTRUCTION MANUAL 1
Contents Warranty 2 Description of symbols 3 Specifications 4 Safety instructions 4 Additional safety instructions for drills 6 Additional safety instructions for the charger 6 Additional safety instructions for the battery pack 7 Know your product 8 Unpacking 9 Fitting and removing the battery pack 9 Battery charging 9 To obtain the best life for the battery 9 Battery indicator 9 LED Work area light 10 Using the drill 10 Forward/reverse switch 10 Adjustable torque 10 Inser
Description of symbols Introduction The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. Wear hearing protection. Wear eye protection. Wear breathing protection. Your new GMC power tool will more than satisfy your expectations. It has been manufactured under stringent GMC Quality Standards to meet superior performance criteria.
before use. Many accidents are caused by poorly maintained power tools. f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.
Additional safety instructions for drills be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. To use this tool properly, you must observe the safety regulations, the assembly instructions and the operating instructions to be found in this Manual. All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards.
• • • • • • • • • • • • If you wish to charge a second battery pack, unplug the charger from the mains supply and leave it for at least 15 minutes. After this time you can charge a second battery pack. charging the exact type of rechargeable battery pack as supplied with the charger.Any other use may result in the risk of fire, electric shock or electrocution. The charger and battery packs supplied with it are specifically designed to work together.
Know your product 6 This drill is mainly used for drilling in wood or metal sheet and screwdriving. Use the tool and accessories only for intended applications. All other applications are expressly ruled out. 1. Keyless chuck 2. Torque collar 3. Trigger with variable speed control 4. Forward/reverse switch 5. Side handle 6. Side handle clamp knob 7. Battery pack release tabs 8. Rechargeable battery pack 9. Slim line adaptor 10. Charger 11. LED Lights 12. Battery indicator button 13.
Unpacking 3. Plug in the charger and switch on. The red LED indicator will show power to the adaptor and that charging is taking place. 4. The battery charging time is approximately 3–5 hours. The red LED goes out when the charging cycle is complete. Turn off the charger power supply from the mains and then remove the battery from the line adaptor. Note: The LED will continue to come on and off approximately every 15 minutes after the battery is fully charged.
battery indicator is showing only 1 LED (low) the battery should be removed and put on the charger. Drilling uses the forward mode. The reverse mode is intended for the removal of screws. LED Work area light Adjustable torque The drill has 3 LED lights (11) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on and off depress the LED light switch (13).
tighten on the drill bit. The front section of the chuck needs to be tightened firmly to ensure the drill bit is held securely. 4. To remove the drill bit, hold the rear section of the chuck firmly and rotate sharply the front section of the chuck in a anti-clockwise direction, sufficiently enough to allow the drill bit to be removed. Drilling masonry • This drill is not designed for drilling masonry. Purchase or hire a Hammer drill.
GMC customer assist If your product needs repairing, replacing, technical service or you simply need help or advice, please contact us on our Customer Assist Line 1300 880 001 (Australia) or 0800 445 721 (New Zealand). For prompt service we suggest you log your service request online at www.gmcservice.com.au. Should you not have access to the Internet, please contact our service department on 1300 880 001 (Australia) or 0800 445 721 (New Zealand). 7am – 7pm, 7days a week (AEST).