2005/11 SD-502 SDIO GPS Receiver User Manual
page 2 SD-502 SDIO GPS Receiver User Manual, version 1.2 1.
page 3 SD-502 SDIO GPS Receiver User Manual, version 1.2 2. System Specification Electrical Characteristics (Receiver) Chipset Frequency SiRF Start III L1, 1575.42 MHz C/A Code 1.023 MHz chip rate Channels 20 channel all-in-view tracking Accuracy Position Horizontal Velocity Time 10 meters, 2D RMS 1~5 meters, 2D RMS with WAAS corrected 0.1 m/sec 1 micro-second synchronized to GPS time Datum Datum WGS-84 (default) Acquistion Rate Hot start 1 sec., average Warm start 38 sec.
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 4 3. Introduction SD-502 is a GPS Receiver with SDIO (Security Digital Input/Output) interface and an integrated built-in memory, which provides an impressive data capacity. The built-in 512 MB memory allows you to easily organize, store, and share files or documents. It also allows for tracking signals and large map data according to the mapping software usage. It’s sleek and stylish design of look can go with any kind of the Pocket PC.
SD-502 SDIO GPS Receiver User Manual, version 1.2 3.
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 6 4. Install Driver You have to install the driver before you can use the SD-502 GPS receiver with your Pocket PC. The driver will be installed into the Pocket PC via the ActiveSync program. So, before you start, please make sure the ActiveSync has been installed and the Pocket PC is connected to your desktop PC. (1). Put the CD into CD-ROM drive. The AutoRun will start the installation program automatically.
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 7 (3). Click Yes and OK on next 2 dialog boxes. Now the driver has been installed in your PDA. (4). Click Exit button to close the AutoRun program.
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 8 (5). If you want to check whether the driver has been properly installed or not, please do the following steps. In your PDA, tap Start / Settings, tap System tab and then Remove Programs icon. You will see the driver “LEADCHAIN GPSDisk” is on the list. (6). If you want to check version information of the installed driver. Please tap Start / Programs / File Explorer, go to “My Device / Windows” folder and open the “GPSDiskVersion.txt”.
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 9 5. Test the SD-502 GPS Receiver You can use the testing program to see if the GPS Receiver is working correctly or not. The testing program only supports the Microsoft Windows CE and Pocket PC based PDA platform. Note : For more detail about this GPSinfo testing program, please refer to the GPSinfo User Manual, you can find it in the root of CD. (GPSinfo_User_Manual_Eng.pdf) To install the testing program, please follow the steps below: (1).
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 10 (3). Click Yes and OK on next 2 dialog boxes. Now the GPSinfo program has been installed in your PDA. (4). Click Finish button and finish the installation and click Exit button to close the AutoRun program.
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 11 (5). If you want to check whether the program has been properly installed or not, please do the following steps. In your PDA, tap Start / Settings, tap System tab and then Remove Programs icon. You will see the “GPS Information GPS Info” is on the list.
SD-502 SDIO GPS Receiver User Manual, version 1.2 page 12 FCC Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation . FCC RF Exposure requirements: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
