BTT-100 / Globalsat BTT-100 User Manual Version 0.9.
Table of Content Overview ........................................................................... 3 Features and Specification ................................................ 4 Features................................................................................ 4 Specification .......................................................................... 4 Accessories............................................................................ 6 Getting Started..........................................
Overview Power status LED GPS status LED Bluetooth status LED Power button Power jack TMC antenna jack 3
Features and Specification Features y New SiRF GSC3 high performance and low power consumption chipset y Communication with Host Platform via Bluetooth Serial Profile y Built-in ceramic patch antenna y Support NMEA 0183 data protocol y 3 LED to show the status of GPS/Bluetooth/Battery y Rechargeable Li-ion battery y Operation time: 14 hours, in continuous mode y Auto power-off, if Bluetooth is not connected to any device within 10 minutes y Bluetooth operation range: 10m Specification Stan
Channels: Antenna Type: Position: Velocity: Time: Default datum: Reacquisition: Hot start: 20 channel all-in-view tracking Built-in patch antenna 10 meters, 2D RMS 5 meters, 2D RMS, WAAS enabled 0.1 m/s 1 us synchronized to GPS time WGS-84 0.1 sec., average 1 sec., average Warm start: 38 sec., average Cold start: 42 sec., average Altitude Limit: Velocity Limit: Acceleration Limit: Jerk Limit: 18,000 meters (60,000 feet) max. 515 meters/ second (1000 knots) max.
Accessories Before you start up, make sure that your package includes the following items. If any item is missing or damaged, please contact your dealer immediately.
Getting Started ► Power Switch Power on: Press the power button 1 second until the GPS status LED is on. Power off: Press the power button 1 second until the GPS status LED is off. ► LED Function Power Status LED (Red/Yellow): Red: Battery power is critically low. Charge it immediately. Yellow: Battery is charging now. LED off: Battery is partially full or fully charged.
the battery power, and all the LED will go off simultaneously. ► Power jack You can use either the DC car power charger (included) or the AC adapter (optional) to connect to the power jack of BTT-100 to recharge the internal battery. Please note that the adapter rating 5V, 1.2 A, positive pole center. ► Usage Connect BTT-100 to your Bluetooth device (1) Press the power button to turn on the BTT-100.
► Connect BTT-100 to a "Windows Mobile Version 5 Pocket PC" 1. Tap on the Bluetooth button on 3. Check “Turn on Bluetooth”. right lower corner. 2. Turn on your Bluetooth GPS receiver. 4. Tap the “Devices” tab, and tap “New Partnership…”. 9 5. It will search for all the Bluetooth devices. 6.
“BT-GPS-328EB2”) and tap Next. 7. Enter Passkey “0000” and tap Next. 8. Check “Serial Port” and tap Finish. 9. The device will be shown on the 10. Tap the “COM Ports” tab, and list. select “New Outgoing Port”.
. Select the device and tap Next. 12. Uncheck “Secure Connection” and from the drop down box select a COM port number (for example, COM8), and then tap Finish. 13. The device with it’s COM port number will be shown on the list. 11 14. Now you can go to GPSinfo program, set the correct COM port and test the GPS receiver.
Software Application ► Connect BTT-100 with your Pocket PC 1. Tap on the Bluetooth button to enable the Bluetooth of Pocket PC and tap on the “Manager” button. 2. Turn on the power of the 4. Tap on “Explore a Bluetooth device” to search the available BTT-100. Bluetooth devices around you. 3. Tap on “New”.
5. Tap on “BTT-100” icon. 6. Tap on “Next”. 7. Tap on “Finish”. 8.
9. The Pocket PC will connect to the BTT-100. ► Test the RDS function 1. Copy the RDS Test program “RDS.EXE” from CD-ROM to your Pocket PC’s internal memory or storage card. 2. Locate the “RDS.EXE” and tap on it to start the program.
3. Set the COM Port to “COM7:” and Baud Rate to “38400”. 4. Set your RDS frequency number and tap on “Set Frequency” button to take effect. 5. Tap on “Connect” button and check the “RDS2 Message ON”. 6. Tap the “Save” button, you can save the RDS message to a Text file. 7. In “GPS” tab, it shows the 8. In “Message” tab, it shows GPS information. the received messages.
9. In the “Information” tab, it shows the RDS information. 10. Signal Quality is ranged from 0 to 15; larger value represents the better quality.
Troubleshooting ► Change battery 1. Press and slide the battery cover to the direction as shown in the figure. 2. Lift to remove the battery cover. 3. Pull the plastic tag to remove the battery.
► Bluetooth is unable to be connected (1) Check if the Bluetooth status LED is flashing normally. (2) Check if the battery power is enough. If not, please recharge it. (3) Check if the other Bluetooth device is enabled or not. ► GPS cannot be positioned (1) Check if the GPS status LED is flashing normally. (2) Check if the battery power is enough. If not, please recharge it.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
