TR151-SP Smart Pallet Tracker User Manual Version 1.
Table of Content 1. Introduction and Features.............................................................................................. 3 1.1 Introduction ............................................................................................................. 3 1.2 Features................................................................................................................... 3 1.3 Hardware ..................................................................................................
1. Introduction and Features 1.1 Introduction TR151-SP is a durable and water resistant GPS/GSM/GPRS tracker. Users can install TR151-SP on vehicles or assets for tracking. It can send out SMS with its location (longitude and latitude) to user’s cell phone by GSM network or to personal computer by internet connection of GPRS network. Then users can track the location of their vehicles or assets. TR151-SP is designed to equip with high capacity of Li-ion battery for long operation time.
1.3 Hardware GSM module: Operating temperature: Charging temperature Antenna Type: Dimension: MC55i GSM 850/900/1800/1900 -20° to 55° C 0° to 45° C GPS patch antenna 128x105x68 mm, for rectangular part 128x130x68 mm, including reset/USB extrusion part Battery: Interface: Button: 15 A rechargeable Li-ion battery Mini USB port for purpose of firmware upgrade, battery charging Reset Button: Press the Reset Button for 3 seconds to reset the device Note: 1. Device is always on until the battery runs out. 2.
2. Start-up 2.
2.2 Install SIM card 1. Remove all 4 screws from the bottom of the device. 2. Carefully, pull both sides apart. This will reveal the insides of the TR151-SP.
格式化: 項目符號及編號 3. Inside, you’ll find a battery, a TR151-SP, a USB extension cable and a reset button. 4. Carefully, unplug the battery from the TR151-SP and the reset button. 5. 6. 7. Unplug the TR151-SP from the USB extension and remove the TR151-SP from the casing. Open the SIM holder. Install the SIM card and close the SIM holder. 8. Plug everything back together as shown below. 9. Once everything is plugged in, put the two halves back together.
10. Screw in the four screws and you’re done.
2.3 How to Turn on/ Charge/ Reset Device is always on until battery exhausted. Charging: Before using TR151-SP for the first time, please fully charge it by connecting to AC power adapter for at least 23 hours (The attached battery is specially designed for TR151-SP.) Reset: Reset button: Pressing the Reset Button for 3 seconds will reset the device.
4. Operating the TR151-SP 4.1 How to set TR151-SP to immediately report its position? Users can make TR151-SP to do SMS or/ and GPRS immediate report of its location by the command media of SMS or GPRS. .
NOTE: 1. The coordinate unit of report format 0 is degree. The coordinates unit of report format 1 is degree and minute with a 4-digit decimal fraction 2. If TR151-SP can not get fixed the position within the “Maximum GPS Fixing Time”, it will 3. return the previous location. Please refer “How to configure TR151-SP by SMS?.” to set “Maximum GPS Fixing Time” Example: If you’d like to ask TR151-SP to send immediate report in format0 to 626-123456 by SMS command media.
4.2 How to set TR151-SP to periodically report its position? Users can make TR151-SP to do SMS or/ and GPRS periodic report of its location by the command media of SMS or GPRS. .
send the SMS of ?2,IMEI,Return_Phone_Number! to stop the periodical report. 3. For the command of “?9,IMEI,Report_Interval,Return_Phone_Number!” and “$9,IMEI,Report_interval!”, TR151-SP would keep connected to GPRS server after it sends the location data. 4. For the command of “?22,IMEI,Report_Interval,Report_Phone_Number!” and “$22,IMEI,Report_Interval,Report_Phone_Number!”, TR151-SP would disconnect from GPRS server after it sends the location data.
4.3 How to set TR151-SP to make GPRS period and disconnect report? Users can make TR151-SP to make GPRS periodic and disconnect report by the command media of SMS or GPRS. What’s different from GPRS periodic report is that for GPRS disconnect and period report, TR151-SP would disconnect from GPRS server after it sends the periodic report. For GPRS periodic report (the command start with “?9” and “$9”), TR151-SP would keep connected to GPRS server after it sends the periodic report.
You have to enter “?10,355632000166323,120,6261234567! Example 2: Require 180-sec period report sent to 626123456 by GPRS command media $10,355632000166323,180! Stop GPRS disconnect and periodical report: Users can send an SMS to stop periodical report.
4.4 How to set TR151-SP enter Geo-fence mode? Users can set up to 10 permissible or restricted areas whose shape is circular or rectangular for TR151-SP to track the vehicles or monitor the equipment/assets. The command media could be SMS or GPRS. Users can choose to receive alarm message while TR151-SP enters the restricted areas or to receive alarm message while TR151-SP gets out the permissible areas.
out the permissible areas. Report_Interval Time interval of sending data report. The unit is second. Set how many reports will be sent? Number_of_Reports Number_of_Reports=0 Æ continuous report Number_of_Reports=X Æ X times report Report_Format Set TR151-SP to return message by Format0 or Format1. (see description below) Return_Phone_Number ?4: The phone number for receiving return message and alarm message.
Command 3: ?4,IMEI,C,longitude,latitude,radius,In_or_Out,Report_Interval, Number_of_Reports,Report_Format,Return_Phone_Number! If user uses numerous SMS in one setting, the IMEI, In_or_Out, Report_Interval, Number_of_Reports, Report_Format, Return_Phone_Number must be the same between each SMS. If above parameters are not the same between SMS, TR151-SP only follows last SMS.
SMS2: ?4,355632000166323,C,E12228.1883,N2442.8117,1000,out,120,10,1,616123456! SMS3: ?4,355632000166323,C,E12328.1883,N2542.8117,1500,out,120,10,1,616123456! Exit Geo-fence mode: Users can send an SMS exit Geo-fence mode. The format of SMS is following as: ?2,IMEI,Return_Phone_Number! Users can also exit from geo-fence mode by GPRS command “$2,IMEI!” Caution: If you exit Geo-fence mode, all the settings will be deleted.
4.5 How to set TR151-SP enter motion mode? You could send command to ask TR151-SP to enter motion mode by SMS command media or GPRS command media. Under motion mode, in addition to the static report interval, TR151-SP will send out the motion report when it senses vibration. If you’d like to continually get the location information of the vehicle installed with TR151-SP, you could make TR151-SP enter motion mode.
“?IMEI,17,GPS_Fix,Date,Time,Longitude,Latitude,Altitude,Speed,Heading,Number_of_Satellite s_In_Use,HDOP!”. (For details of the data, please refer to SMS Report Format) When TR151-SP senses vibration over the value of the sensitivity for the first time, it will send the motion report like “?IMEI,24,GPS_Fix,Date,Time,Longitude,Latitude,Altitude,Speed,Heading,Number_of_Satellite s_In_Use,HDOP!”.
You can send command as: “$16,355632000166323,3,60,90,10,9095978525! TR151-SP will send “$OK!” to the GPRS server TR151-SP will send regular report every 60 minute to GPRS server and 909-597-8525 like “$,355632000166323,17,3,301008,125935,E12129.2616,N2459.7918,97.2,0.13,142.31,04,2.4! When TR151-SP senses vibration over 5 times for the first time, it will send the motion report to GPRS server and 0966339154 like “$,355632000166323,24,3,311008,114550,E12140.1444,N2455.8118,95.3,10.22,142.31,04,2.
5 Configuration 5.1 Read Configuration 5.1.1 How to send SMS and ask TR151-SP for sending back its configuration by SMS? You can send SMS to TR151-SP to ask it to send SMS with its configuration setting. The format of the SMS is “?7,IMEI,0,Return_Phone_Number!” Format Description ? Start sign 7 Function code IMEI IMEI code of the TR151-SP 0 Report type of reading configuration Report Phone Number The phone number for receiving TR151-SP configuration.
configuration setting. The format of the SMS is “$7,IMEI,0,Return_Phone_Number!” Format Description $ Start sign 7 Function code IMEI IMEI code of the TR151-SP 0 Report type of reading configuration Report Phone Number The phone number for receiving TR151-SP configuration. ! End sign TR151-SP will return 3 pieces of SMS with its configuration. For details, please refer to TR151-SP Configuration Content 5.1.
5.2 Write Configuration 5.2.1 How to configure TR151-SP by SMS? You can send SMS to configure following parameters into TR151-SP. There are 9 settings as below.
SMS Default Report Phone Number: Set SMS Default Report Phone Number. Maximum_GPS_Fixing_Time: If GPS is not fixed within the time, it returns previous location and close GPS. The unit is minute.
3. GPRS Server Host Name is the physical IP address of the PC that you installed the call center or a domain name. The IP is for connecting the GPRS network. It should be a physical IP. 4. In Taiwan, GPRS user name, GPRS user password, GPRS DNS1, and GPRS DNS2 are not necessary items. You have to consult with your GPRS network provider about those values.
5.2.2 How to configure TR151-SP by GPRS server? You can send command by GPRS server to configure following parameters into TR151-SP. There are 9 settings as below.
Default_Report_Mode = 22 Æ SMS and GPRS period report Enable_SMS_Default_Report_Phone_Number: Enable or disable SMS Default Report Phone Number. Enable_SMSDefaultReturnPhoneNumber = 0 Æ Disable Enable_SMSDefaultReturnPhoneNumber = 1 Æ Enable Number_of_Reports: Set how many report will be sent. Number_of_Reports = 0 Æ continuous report Number_of_Reports = X Æ X times report Report_Format: Ask TR151-SP to return message by Format0 or Format1. Report_Interval: Time interval of sending data report.
On-line Setting: Enable/disable_GPRS_on-line: 0=disable 1=enable Æ Enable/disable_GPRS_on-line in motion mode (the report method must be GPRS) Disconnect and reconnect interval: interval for cutting GPRS connection and re-connect it. The unit is second.
5.3 TR151-SP Configuration Content Example: TR,IMEI,1,1,3,30,1,30,0,12,30,0,Tony,+8.00,1,60,1,0,0,1,0,1,1800! Parameters Description TR Start sign IMEI IMEI 1 Sequence Enable/ Disable SMS Default 0: Disable, 1: Enable Report Phone Number Maximum GPS Fixing Time The maximum time for getting GPS fix.
Example: TR,IMEI,2,18883238720,19095978525,19095973805,19095973058,18883238730,19095973179,19095973179! Parameter Description TR Start sign IMEI IMEI 2 Sequence SOS Number 1 Set SOS Number 1 SOS Number 2 Set SOS Number 2 SOS Number 3 Set SOS Number 3 Default Report Number Report phone number SMS Report Number Report phone number of SMS report Motion Report Number Report phone number of Motion mode reporting SMS ! End sign Example: TR,IMEI,3,5000,internet,,,,,220.128.207.
6 Report Format 6.1 SMS Report format SMS Report format from TR151-SP The data format is configurable in the SMS tracking commands. There are two types of the data format as below. Format0 is for general end users who send SMS commands to TR151-SP by their cell phone or PDA phone. This format is very easy to read by end users. Format1 is specifically read by software Call Center that is developed by service provider.
date ddmmyy time hhmmss longitude (E or W)dddmm.mmmm Example: E12129.2186 → E 121°29.2186’ latitude (N or S)ddmm.mmmm Example: N2459.8915 →N 24°59.8915’ altitude xxxxx.x unit: meters speed xxxxx.xx unit: knots (1knots = 1.
6.2 GPRS Report Format Format of report GPRS from TR151-SP Format: Command_Head,IMEI,status,GPS_fix,date,time,longitude,latitude,altitude,speed,heading,number of satellites in use,HDOP,Command_End Example: $355632004245866,1,1,040202,093633,E12129.2252,N2459.8891,00161,0.0100,147,07,2.4! Format Value Command_Head $ Note IMEI (The number of IMEI) Report Mode 2 2: Stop connect 5 5: SOS(Alarm) 8 8: GPRS Immediate report 9 9: GPRS Period report 10 10.Disconnect and GPRS period 11 11.
6.3 Cell ID Report Format Format of GPRS report with Cell ID from TR151-SP GSM Cell ID is assisted information to get device location. When TR151-SP does not get GPS fix, you could enable TR151-SP to report the Cell ID. Note: If you want TR151-SP to report the Cell ID, please configure TR151-SP by SMS with the content “?7,IMEI,C,Enable/disable _Cell_ID,Report_Phone_Number!” or by GPRS with the content “$7,IMEI,C,Enable/disable _Cell_ID,Report_Phone_Number! For details, please refer to 1.
date ddmmyy time hhmmss MCC Mobile Country Code 3 digits MNC Mobile Network Code 2 or 3 digits LAC Location Area Code 4 hexadecimal digits CID Cell identifier 4 hexadecimal digits BSIC Base Station Identity Code 1 digit or 2 digits RSSI Received Signal Strength Indicator 1 digit or 2 digits Command END ! Note: TR151-SP TR151-SP is designed for vehicle and asset for tracking purpose, not for carried by people.