Model #: Serial #: Model SP20 Instruction Manual for Globe Mixers Models SP10, SP20, SP25, SP30, SP30P, SP40, SP60, SP62P, SP62P-4 and SP80PL For Service on Your Mixer, call Globe Technical Support at 1-866-260-0522. - IMPORTANT SAFETY NOTICE This manual contains important safety instructions which must be strictly followed when using this equipment. Visit our website for information on additional products available from Globe. www.globefoodequip.
Index ATTENTION OWNERS AND OPERATORS.................................................................................................................4 KEY COMPONENTS OF THE MIXER.........................................................................................................................5 INSTALLATION........................................................................................................................................................ 6-7 OPERATING INSTRUCTIONS..................
Attention Owners and Operators Globe equipment is designed to provide safe and productive processing of food products as long as the equipment is used in accordance with the instructions in this manual and is properly maintained. Unless the operator is adequately trained and supervised there is a possibility of serious injury.
Key Components of the Mixer Minute Up/ Down Controls Digital Timer Display Seconds Up/Down Controls Start Button Stop Button Attachment Hub Thumbscrew Attachment Hub Bowl Lift Lever Planetary Grease Fitting Bowl Guard Handle Planetary Shaft Bowl Lift Wheel (Models SP40 and SP60) Bowl Handle Bowl Clamp SP20 FRONT VIEW Power Bowl Lift, Mode & Timer Controls (Models SP62P and SP80PL) Gear Oil Meter (Models SP62P and SP80PL) Speed Control Bowl Guard Splash Guard Built in Ingredient Chute Bowl Bowl
Installation UNPACKING Unpack the mixer immediately after receipt. If the machine is found to be damaged, save the packaging material and contact the carrier within fifteen (15) days of delivery. Immediately contact your source of the equipment. You have no recourse for damage after fifteen (15) days. TO AVOID SERIOUS PERSONAL INJURY: • • • • • ALWAYS install equipment in work area with adequate light and space. ONLY operate mixer on a solid, LEVEL, non-skid surface that is nonflammable.
Installation CONNECTING TO ELECTRICAL POWER cont’d. If the unit needs to be hard-wired, have a licensed electrician connect the unit to the power supply. Three Phase Units: Before use, confirm proper rotation of all 3 phase mixers. There is a 50% chance your 3 phase mixer is properly rotating if you are using it on 3 phase power. 1. Make sure there is not a mixing tool on the mixer shaft and the bowl is empty. 2. Put the speed lever on one speed and turn the unit on. 3.
Operating Instructions 2. To rotate bowl guard to its open position, grasp the separated handles on bowl guard and move them together as one, clockwise to open/rotate bowl guard. To close bowl guard, grasp the separated handles and move them together as one, counterclockwise to close/rotate the bowl guard back into a locked position.
Operating Instructions ATTACH AGITATOR TO MIXER (i.e., Beater, Hook, Whip) NOTE: It is easier to install the agitator before adding the ingredients into the bowl. 1. Rotate bowl guard to the left so it rests in the open position (Fig. 9-1). Using excessive force to open and close bowl guard can damage the spring lock and bowl guard microswitch and will void the warranty. 2. Slide the agitator slowly upwards onto the planetary shaft, fitting the shaft pin through the slot in the agitator (Fig. 9-2). Fig.
Operating Instructions Always STOP mixer BEFORE changing speeds. Failure to do so can damage the gears or other parts and WILL void the warranty! 6. To change the speed while mixing: a. Press the red STOP button, then wait for the agitator to come to a complete stop. b. Change the speed by raising or lowering the speed control lever. c. Press the green START button to restart the mixer.
Operating Instructions Before starting mixer: Always change speeds BEFORE starting mixer. Failure to do so can damage the gears or other parts and WILL void the warranty! USING MIXER’S DIGITAL CONTROLS AND TIMER Read through this section and continue to page 13 for further operating instructions for use of the digital controls on your mixer. Mixer is equipped with a digital timer display, minutes and seconds buttons (to adjust the timed operations) and Start / Stop buttons.
Operating Instructions HOW TO USE ATTACHMENT HUB Never put your hand into the feed chute when using a mixer attachment. Only operate the attachment hub in MANUAL mode. DO NOT attempt to mix ingredients in bowl while using the hub. Mixer must be OFF before installing attachment. Do NOT use attachments while mixing. 1. Loosen and remove attachment hub thumbscrew (Fig. 12-1). 2. Remove plastic cover from attachment hub (Fig. 12-1). Thumbscrew Plastic Cover 3.
Operating Instructions DIGITAL CONTROL INSTRUCTIONS Untimed / Manual Mode instructions and controls for the SP62P, SP62P-4 and SP80PL Mixer must be OFF before installing attachments. Do NOT use attachments while mixing. NOTE: Make sure bowl is up and bowl guard is closed. Mixer will not start if bowl and bowl guard are not in the proper operating position. Press BOWL “Up” arrow to activate the power bowl lift. Set the speed control to the desired speed. 2 Untimed - MANUAL MODE 1.
Operating Instructions 4 4. Once the START button is pressed, mixer timer numbers will begin to descend. The timer and mixer can be interrupted at any time by pressing the STOP button. If the timer cycle is interrupted and the mixer has not yet finished its set mixing time, the mixing cycle can be continued from where it left off by pressing the START button. NOTE: If a cycle is interrupted by the bowl guard being opened or the speed of the mixer being changed, mixer will stop.
Cleaning Instructions • Dilute detergent per supplier’s instruction. • DO NOT hose down or pressure wash mixer. • NEVER use a scrubber pad, steel wool, or abrasive material to clean mixer. • NEVER use bleach (sodium hypochlorite) or bleach-based cleaner. • ALWAYS remove the agitator after each batch as the agitator can become stuck on the shaft and become difficult to remove.
Important Points Globe mixer will provide years of uninterrupted service if you do the following: Installation • Do not use an extension cord to connect electrical power. • Make sure all 3 Phase units (see data plate) run in the direction of the arrow on front of the machine. Operation • Turn off mixer before changing speeds. • Follow the Capacity Chart for mixing dough. Refer to Capacity Chart section. • Use only first (1) speed for mixing dough.
Capacity Chart The following maximum capacities are intended as a guideline only. Varying factors such as the type of flour used, temperature of water used and other conditions may require the batch to be reduced. Product Agitator and Speed SP5 SP8 SP10 SP20 SP25 SP30/ SP30P SP40 SP60 SP62P SP62P-4 SP80PL Waffle or Hotcake Batter Flat Beater 2 qts. 3 qts. 5 qts. 8 qts. 10 qts. 12 qts. 16 qts. 24 qts. ---- 24 qts. 30 qts. Whipped Cream Wire Whip 2 qts. 2 qts. 2 qts. 4 qts.
Troubleshooting Problem Mixer will not operate Mixer stops during mixing cycle Possible Causes Action Required Bowl guard not in closed position. Rotate guard to the right until fully closed. Bowl not raised. Raise bowl to highest position. Power not connected properly. Check all power connections. Plug into a live socket. (Do not use extension cord!) Test socket with another item. Building circuit breaker is off. Check breaker box. Internal overload tripped.
Troubleshooting Problem Mixing time is too long Possible Causes Action Required Three-phase mixer is wired wrong Agitators must rotate clockwise around bowl. If not, electrician must rewire Batch size too small Increase batch size or use smaller bowl adapter kit.
Limited Mixer Warranty Globe Food Equipment Company (“GFE”) warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions within North America and subjected to normal use, is free from defects in material or workmanship for a period of 2 years. Wear parts, such as belts, are excluded. Hub attachments, such as shredders, slicers and grinders have a 1 year warranty that only covers parts.