Atmosorb Domestic ventilation system with heat recovery and wired remote control Instructions for Use To b e l e f t w i t h t h e u s e r www.glow-worm.co.
WARNING SHEET METAL PARTS This unit contains metal parts (components) and care should be taken when handling and cleaning, with particular regard to edges. SEALED COMPONENTS Under no circumstances must the User interfere with or adjust sealed parts. Customer service call: 01773 596510 Technical helpline: 01773 828300 General and Sales enquiries Tel: 01773 824639 Fax: 01773 820569 2 www.glow-worm.co.
14864 HRD 275 HRD 350 www.glow-worm.co.
CONTENTS Important Information 5 Ventilation/Heat Recovery Unit Design 8 Operating Instructions 9 Description 10 Operation 11 User Controls 12 Cleaning the Filters 18 These instructions are an integral part of the appliance and must be left with the user. Please read these instructions and follow them carefully for the safe and economical use of your boiler. 4 www.glow-worm.co.
Important Information Control of Substances Hazardous to Health CE Label Under Section 6 of The Health and Safety at Work Act 1974, we are required to provide information on substances hazardous to health. The CE label shows that the Atmosorb ventilation unit complies with the basic requirements of the following directives and guidelines: The adhesives and sealants used in this appliance are cured and give no known hazard in this state.
Important Information Operation The Atmosorb can only be used if all ventilation pipes are connected and the unit is closed. The Atmosorb unit must only be operated with the supplied filters installed. Regularly check whether the filters are dirty or damaged. We recommend to visually check the filters every 6 months and to replace them every 12 months, or after 2000 operating hours at the latest.
Important Information Cleaning The Atmosorbs casing can be cleaned using a mild liquid detergent with a damp cloth, then a dry cloth to polish. Do not use any form of abrasive or solvent cleaner as you may damage the paintwork. The filters on the Atmosorb or bypass, can be cleaned with a vacuum cleaner, DO NOT clean with water or any other liquid. See section "Cleaning the Filters". Recycling and Disposal The Atmosorb as well as the packaging, consist mainly of recyclable raw materials.
Ventilation/Heat Recovery Unit Design Description Electrical Supply Failure The domestic ventilation unit consists of a central ventilation appliance for air exchange with heat recovery and a remote control. For summer operation, you can obtain a bypass as an accessory. It can directly provide living rooms with cool external air whenever it is necessary. The external air flow bypasses the heat exchanger.
Operating Instructions Intended Use The Glow-worm domestic ventilation units are built and designed according to accepted safety rules and regulations. Nevertheless, improper use can cause serious or fatal injury to the user or others, and the appliance or other property can be damaged. This device is not designed to be used by persons (including children) unless they are supervised by someone who is responsible for their safety or have been instructed how to use the device.
Description 14876 OUTSIDE AIR BYPASS EXHAUST AIR DISCHARGE AIR Designation Explanation Fresh air From the Atmosorb to the living room Exhaust air From the living space to the Atmosorb Outside air From outside to the Atmosorb Discharge air From the Atmosorb to outside FRESH AIR 14875 AERATION WITH THE OUTSIDE AIR FILTER FRONT PANEL AIR DUCT CONNECTIONS 10 Diagram 1 BYPASS www.glow-worm.co.
Operation Bypass (optional) The Atmosorb can be equipped with a bypass, which is fitted on the top of the device, see diagram 2. With a bypass installed the user may operate the so-called "free cooling mode" during the summer months with the outside temperature falling below room temperature during the night. The cooler outside temperature will not be warmed by the device before it was blown into the room.
User Controls Meaning Special function - Energy-saving SPECIAL FUNCTIONS Special function - Advance Special function - Holidays Static: Flashing: Off: Static: Flashing: Off: 2nd fan stage (day mode) 3rd fan stage (HIGH) 1.
User Controls 15541 Diagram 4 From the basic display you can select and change the major functions by pressing the "mode" button and then the - or + buttons to change their values. By pressing the "mode" button you can move from one menu item to another. Press the "mode" button until you have reached the desired function/menu. Press the - or + buttons to achieve the desired value. NOTE: After the necessary settings have been made, no confirmation is required.
User Controls Automatic operation: The change between the day and night operation occurs automatically. Additionally, the current operating mode is displayed. Minimum operation: Irrespective of the time programme the remote control switches the fans into the lowest stage. Check and setting of the time Press "mode" several times in order to select days of the week, hours and minutes as required. The selected category flashes in the display. Press - or + to change days of the week, hours and minutes.
User Controls Programming of the Clock Timer With the programming button you can change the times for the timer mode. With activated timer function, Atmosorb will switch between the first and the second stage (timecontrolled). ● Outside the time window: Stage 1 = night mode ● Within the time window: Stage 2 = day mode ● Press the "prog" button again to show the end time, press the - or + to change the flashing value. ● Terminate programming of the operating time by pressing the "mode" button.
User Controls Special functions From the basic display you select the function by pressing the "prog" button. NOTE: After the necessary settings have been made, no confirmation is required 10 seconds after the last input the indicated function is automatically activated and then the display returns to the basic display. Holiday function: If you select the holiday function, the fan stage is set to a minimum value for a period (in days) of up to 99 days.
User Controls Information Level ● DATE Press and hold the "prog" button to reach the info level. In addition to identifying the controller, the information level is used to quickly and easily check the set operating times. Each time window may be individually opened. The current date is displayed. To return to the basic display press and hold the "prog" button. Prerequisite is to activate the calendar first. ● H1, H2 and H3 Timer settings.
Cleaning the Filters Continued efficient operation, reliability and a long service life as well as safety, require inspections and maintenance work to be regularly carried out by a competent person approved at the time by the Health and Safety Executive and on an annual basis. Cleaning or Replacing the Filter We recommend making a maintenance agreement. The operational reliability of the device can be impaired, resulting in damage to property or personal injury, if maintenance work is not carried out.
www.glow-worm.co.
Glow-worm, Nottingham Road, Belper, Derbyshire. DE56 1JT 0020088554-01 08.09 Because of our constant endeavour for improvement, details may vary slightly from those shown in these instructions.
