Manual

ManualsBrandsGlowShift ManualsFor the carDigital Series Wideband Air_Fuel Ratio Gauge

Digital Series Wideband Air/Fuel Ratio Gauge with Data Logging Output

For Product Numbers: GS-BD02W and GS-RD02W

Wire Color Code

Red:

12v Constant Source (+) (un-switched)

Black:

Vehicle Ground ( - )

White:

12v Ignition Source (+) (switched)

Orange:

12v Switched Headlamp Source (+) (optional)

1. Disconnect the negative battery cable.

2. Mount the controller inside the vehicle away from heat, water,

moisture, dirt and all moving parts, in an easily accessible location.

This allows for the unit to be accessible should calibration need to be

performed.

3. Install the provided LSU 4.9 Sensor by welding the matching

exhaust bung to the exhaust pipe.

 Note: We recommend using Anti-Seize on the bung threads so

that you can unscrew the sensor when necessary.

 Note: Make sure the location of the bung is a minimum of 6

inches after the exhaust ports, but before the catalytic converter,

and no more than 36 inches from the last exhaust port.

 Note: The bung must be installed to the top or side of the

exhaust pipe at a minimum of 10 degrees for the top and 15

degrees for the side from a horizontal position with the

electrical connection up to prevent a collection of liquid at the

element during the warm up phase.

4. Next, route and secure the sensor wire harness from the sensor into

the vehicle, close to the controller’s location. Be sure to use a

grommet when routing the wires through the firewall to protect them

from stripping.

5. Connect the red wire to a positive 12 volt constant (un-switched)

source either directly to the battery or to a fuse panel on the vehicle.

If wiring to an un-fused source, install a 3 amp fuse inline within 20

inches of the sources connection.

6. The white wire should be connected to a positive 12 volt ignition

(switched) source. It may be connected to the fuse panel, an accessory

wire, or any positive 12 volt source that turns on and off with the ignition

7. Connect the black wire to any good (unpainted) ground connection.

You may also route a wire directly to the negative side of the vehicle’s

battery.

8. The Night Time Dimming feature decreases the brightness of the gauge

face by 30%. Connect the orange wire to the 12 volt positive headlamp

source. This allows the mode to be activated when the headlights come

on. This step is optional and will not affect operation of the gauge if it is

omitted. NOTE: Do not connect the orange wire to a dimmer wheel.

This will cause the gauge lighting to flicker.

9. Reconnect the negative battery cable.

Summary of content (4 pages)

PAGE 1
Digital Series Wideband Air/Fuel Ratio Gauge with Data Logging Output For Product Numbers: GS-BD02W and GS-RD02W Red: White: 12v Constant Source (+) (un-switched) 12v Ignition Source (+) (switched) Wire Color Code Black: Vehicle Ground ( - ) Orange: 12v Switched Headlamp Source (+) (optional) 1. Disconnect the negative battery cable. 4. 2. Mount the controller inside the vehicle away from heat, water, moisture, dirt and all moving parts, in an easily accessible location.
PAGE 2
Calibration Schedule Prior to calibration remove the sensor from the bung. This will ensure a proper calibration. To obtain the most accurate results from your gauge, please follow the calibration schedule pre and post installation: A. For Everyday Driven Vehicles  Calibrate after installation.  Calibrate again, after 3 months of use.  Calibrate twice a year or every 10,000 miles (whichever comes first). B. For Race Vehicles  Calibrate after installation.  Calibrate once per race weekend. C.
PAGE 3
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER GlowShift Gauges, LLC ("GlowShift") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from defects in material or workmanship for a period of one (1) year from the purchase date. For a period of one (1) year from the date of purchase, at no charge to the Purchaser, GlowShift will repair or replace this Product if it is determined by GlowShift to be defective.
PAGE 4
. PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.