Manual

ManualsBrandsGlowShift ManualsFor the carElite 10 Color Volt Gauge

Elite 10 Color Volt Gauge

For Product Numbers: GS-ET05 & GE-EWT05

Wire Harness Color Code

Red:

12v Constant (un-switched) Source (+)

Black:

Vehicle / Engine Ground (-)

White:

12v Ignition (switched) Source (+)

Orange:

12v Dimmer (switched) Source (+) (optional)

1. Disconnect the negative battery cable.

2. Connect the white wire to a positive 12 volt ignition

(switched) source. It may be connected to the fuse panel, an

accessory wire, or any positive 12 volt source that turns on

and off with the ignition switch of the vehicle.

 Note: If wiring to an un-fused source, install a 3

amp fuse inline within 20 inches of the sources

connection. You may obtain an optional

“expandable circuit” accessory. This component

easily fits into your fuse panel and provides an

additional fused power wire for accessories such as

gauges. This is available at www.GlowShift.com or

a local auto parts store.

3. Connect the red wire to a positive 12 volt constant (un-

switched) source, either directly to the battery or to a fuse

panel on the vehicle.

 Note: If wiring to an un-fused source, install a 3

amp fuse inline within 20 inches of the sources

connection. You may obtain an optional

“expandable circuit” accessory. This component

easily fits into your fuse panel and provides an

additional fused power wire for accessories such as

gauges. This is available at www.GlowShift.com or

a local auto parts store.

4. The Night Time Dimming feature decreases the brightness

of the gauge face by 30%. Connect the orange wire to the 12

volt positive headlamp source. This allows the mode to be

activated when the headlights come on. This step is optional

and will not affect operation of the gauge if it is omitted.

 Note: Do not connect the orange wire to a dimmer

wheel. This will cause the gauge lighting to flicker.

5. Connect the black wire from the gauge, to any good

(unpainted) ground connection. You may also route a wire

directly to the negative side of the vehicle’s battery.

6. Reconnect the negative battery cable.

7. Daisy Chain Feature (Optional): If you are installing

more than one Elite 10 Color Gauge, you can use the daisy

chain feature to power up to 4 additional gauges. Simply plug

the included daisy chain wire into the gauge that is already

powered (port B); then plug the other end of the wire into the

daisy chain port on the next gauge.

Note: If you are daisy chaining the gauges the volt gauge

must be the first gauge in the daisy chain line.

Summary of content (3 pages)

PAGE 1
Elite 10 Color Volt Gauge For Product Numbers: GS-ET05 & GE-EWT05 Wire Harness Color Code Red: White: 12v Constant (un-switched) Source (+) 12v Ignition (switched) Source (+) 1. Disconnect the negative battery cable. 2. Connect the white wire to a positive 12 volt ignition (switched) source. It may be connected to the fuse panel, an accessory wire, or any positive 12 volt source that turns on and off with the ignition switch of the vehicle.
PAGE 2
Operating Instructions 1. 10-Color Mode: 1. Press the COLOR button to cycle between the 10 different color options. 2. The sequence of display colors are: Blue, Green, Red, Yellow, White, Light Blue, Purple, Pink, Orange, Amber. After Amber there are 2 automatic color changing functions on the gauge that begin with the color Blue. They are the 10 Color Cycle Mode and the 10 Color Slow Fade Mode. 2. Setting the Peak Recall: 1.
PAGE 3
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER GlowShift Gauges, LLC ("GlowShift") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from defects in material or workmanship for a period of one (1) year from the purchase date. For a period of one (1) year from the date of purchase, at no charge to the Purchaser, GlowShift will repair or replace this Product if it is determined by GlowShift to be defective.