Manual

ManualsBrandsGlowShift ManualsCarTinted Series 0~2400F - Exhaust Gas Temperature Gauges

Tinted Series – 0 ~ 2400F - Exhaust Gas Temperature Gauges

For Product Numbers: GS-T08

Wire Color Code

Black

Vehicle Ground (-)

Pink

Sensor Connection (+ PINK)

Red

12v Ignition (switched) Source (+)

Blue

Sensor Connection (- BLUE)

Orange

12v Dimmer (switched) Source (+) (Usually Headlights)

1. Disconnect the negative battery cable.

2. Using automotive grade wiring (18 gauge), connect the

red wire to a positive 12 volt ignition (switched) source.

It may be connected to the fuse panel, an accessory wire,

or any positive 12 volt source that turns on and off with

the ignition switch of the vehicle.

 If wiring to an un-fused source, install a 3 amp

fuse inline within 20 inches of the sources

connection. You may obtain an optional “add a

circuit” accessory. This component easily fits

into your fuse panel and provides an additional

fused power wire for accessories such as gauges.

This is available at www.GlowShift.com or a

local auto parts store.

3. (Optional) The dimming feature of the Tinted Series

decreases the brightness of the lighted gauge face 30%.

Connect the orange wire to a positive 12 volt switched

source. The most common installation is to splice and

connect to the 12 volt positive headlight source. This step

is completely optional.

4. Connect the black wire to any good (unpainted) ground

connection. You may also route a wire directly to the negative side of

the vehicle’s battery.

5. There are three common types of exhaust temperature probe

installations:

 Exhaust Probe Adapter Fitting: This method is not shown,

but you may purchase an exhaust pipe probe adapter fitting

from www.Glowshift.com or an authorized dealer. This

adapter is clamped and tightened around the exhaust pipe and

provides a 1/8NPT fitting for an EGT probe. After

positioning and tightening of the adapter clamp, you will then

drill your exhaust pipe and then permanently mount the probe

through the fitting and into the exhaust pipe.

 Exhaust Manifold: Drill and tap the exhaust manifold to 1/8

NPT. Install the supplied temp sender with probe fittings,

bushings, ferrel fitting and nut.

 Exhaust Pipe: Drill and tap the exhaust pipe to 1/8 NPT.

Install the supplied temp sender with probe fittings, bushings,

ferrel fitting and nut.

6. Connect the pink & blue temperature probe wires to the pink &

blue wires on the gauge harness.

7. Reconnect the negative battery cable.

 This gauge should never be connected to a dimmer. Connecting

the gauge to any type of dimmer switch unit will cause the gauge

to improperly function.

Summary of content (3 pages)

PAGE 1
Tinted Series – 0 ~ 2400F - Exhaust Gas Temperature Gauges For Product Numbers: GS-T08 Wire Color Code Black Red Orange Vehicle Ground (-) 12v Ignition (switched) Source (+) 12v Dimmer (switched) Source (+) (Usually Headlights) 1. Disconnect the negative battery cable. 2. Using automotive grade wiring (18 gauge), connect the red wire to a positive 12 volt ignition (switched) source.
PAGE 2
Additional Installation Information & Material Requirements  GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gauges may require lengths of wire (sizes and quantity depend on vehicle, gauge type, gauge location and / or sensor location). For correct and proper GlowShift Gauge installation and operation, the use of 18 Gauge (wire diameter) automotive grade conductor wire with sheathing is recommended for one or more gauges per vehicle.
PAGE 3
DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES, GLOWSHIFT HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.