AEC-7763LC/LD & ARS-2022/2022D Chapter 1 Introduction The four models AEC-7763LC, AEC-7763LD, ARS-2022, and ARS-2022D are somewhat different in mechanical design, but have the same functions of duplication. AEC-7763LC and ARS-2022 are simply for copying CD in video, audio or data form while AEC-7763LD and ARS-2022D for copying CD and DVD. They all have multifunctional LCDs and 4 simple buttons on the panels. With any of them duplication will be easier and more efficient. 1.
AEC-7763LC/LD & ARS-2022/2022D Chapter 2 Installation From this chapter on we only take ARS-2022D as an example to explain. The hardware connection of ARS-2022D can be with or without a hard drive. Hardware Connection of ARS-2022D with a HDD The hard drive must be connected to port CN2 and in Master mode. DVD-ROM must be in Slave mode.
AEC-7763LC/LD & ARS-2022/2022D Chapter 3 Basic Instructions 3.1 Buttons and LCD There are four buttons and an LCD on the panel of ARS-2022D. They are described as follows. 1 2 4 3 5 1. It shows all functions and messages. 2. It is used to scroll up functions or menus. 3. It is used to scroll down functions or menus. 4. It is used to execute a selected function. 5. It is used to cancel a selected function.
AEC-7763LC/LD & ARS-2022/2022D There are 12 functions for you to use. Function 1 is Copy. You can press ▼ to see other functions. 3.2 About HDD Installation With a 3.5” hard drive you can use and enjoy the function of Image. In other words, you have one more choice to duplicate a CD or DVD from an image file stored in the hard drive. 3.2.1 With a HDD If you install a 3.5” hard drive to ARS-2022DS, the operation procedures will be as follows.
AEC-7763LC/LD & ARS-2022/2022D 3.2.2 Without a HDD If you don’t install a 3.5” hard drive to ARS-2022D, the operation procedures will be as follows. l l Place a source DVD into DVD-ROM. Switch to function 1 Copy by pressing ▲ . Place a blank DVD disk into the DVD writer, and press ENT to start copying. l When copying comes to an end, the passed DVD will eject automatically. The default is automatic ejecting, but you can change it. l The failed DVD will remain in the writer.
AEC-7763LC/LD & ARS-2022/2022D Chapter 4 Board Layout The board layout of ARS-2022D is shown as follows.
AEC-7763LC/LD & ARS-2022/2022D Chapter 5 Functions There are 12 functions: Copy, Test, Test & Copy, Verify, Compare, Prescan, Disc Info, Select Source, Image, Edit Track, Setup and Advanced Setup. Among the 12 functions, Edit Track is designed exclusively for editing a collection of favorite songs from CDs. During operation if you do not understand an LCD message, you can see Appendix 2. 5.1 Copy Function 1 Copy is to copy data from a source DVD directly into a blank DVD disk.
AEC-7763LC/LD & ARS-2022/2022D When copying comes to an end, LCD will show the results as follows. The passed DVD will eject automatically. 1.Copy OK: 01 5.2 Test Function 2 Test is to simulate the copying progress. When simulation finishes, there will be no data really written into the DVD disk. Select function 2. Put a source DVD onto DVD-ROM and a blank DVD disk onto the DVD writer. 2.Test Press ENT to start simulation.
AEC-7763LC/LD & ARS-2022/2022D When the test comes to an end, LCD will show the results as follows. 2.Test OK: 01 Stopping the test halfway does not affect the DVD disk, but if the DVD rewriteable disk contains important data, they may be destroyed. 5.3 Test & Copy Function 3 Test & Copy is to test first and then copy actually. Select function 3. Put a source DVD onto DVD-ROM and a blank DVD disk onto the DVD writer. 3.Test & Copy Press ENT to start simulation.
AEC-7763LC/LD & ARS-2022/2022D When the whole process finishes, LCD will show the results as follows. 3.Test & Copy OK: 01 5.4 Verify Function 4 Verify is to examine if the target DVD can be read correctly after copying. Select function 4. 4.Verify Press ENT to verify. LCD will show the verification information as follows. Verify- DVD 0% 4213.4MB 15:00 When verification comes to an end, LCD will show the results as follows. 4.Verify OK: 01 5.
AEC-7763LC/LD & ARS-2022/2022D Select function 5. Put the source DVD onto DVD-ROM and the target DVD onto DVD writer. 5.Compare Press ENT to compare. LCD will show the comparison information as follows. Compare- DVD 0% 4213.4MB 15:00 When comparison comes to an end, LCD will show the results as follows. Compare Fail: 0 OK: 1 Diff: 0 Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2.
AEC-7763LC/LD & ARS-2022/2022D If comparison fails, LCD will show the failure. By pressing ENT twice, LCD will show that the contents of source 1 and those of source 2 do not match as follows. Src: 02 DVD-RW TOC not match 5.6 Prescan Function 6 Prescan is to scan if the source DVD can be read correctly, and by the way to test the reading speed. Select function 6. Put the source DVD onto DVD-ROM. 6.Prescan Press ENT to prescan. LCD will show the scanning information as follows. Scaning- DVD 0% 4213.
AEC-7763LC/LD & ARS-2022/2022D 5.7 Disc Info Function 7 Disc Info is to show the basic information of source DVD. Select function 7. Put the source DVD onto DVD-ROM. 7.Disc Info Press ENT, and LCD will show the DVD information as follows. Disc Type: DVD-ROM Capacity: 4213.4MB 5.8 Select Source Function 8 Select Source is to let you select the data on DVD-ROM, DVD writer or HDD as the source from which copying will be done. Select function 8. 8.
AEC-7763LC/LD & ARS-2022/2022D After selecting the source such as DVD-ROM, you can press ENT, and LCD will show the message as follows. DVD-ROM selected! Suppose you select HDD as the source and try to copy from one of its partitions, but the partition contains no data, an error message will appear on LCD. At this moment, you can switch to another partition that contains data, or use function 9 Image to load the data into the chosen partition first. 5.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to load. LCD will show the loading information as follows. Load- A - DVD 0% 4213.4MB 15:00 After the image file is successfully loaded, LCD will show the results as follows. Image load OK If there is an image file existing in the current partition, the system will ask you whether to overwrite it or not. Please use ▲ ▼ to confirm Yes or No. Image Exists Overwrite?Yes 5.9.
AEC-7763LC/LD & ARS-2022/2022D After the image file is deleted, LCD will show the results as follows. Partition A: Image is deleted 5.9.3 Image Info This function is to show the basic information of an image file stored in a particular partition. First, select the function by pressing 9-03.Image Image Info ▼. P: A Press ENT, and LCD will show the information of the image file as follows. Disc Type: DVD-ROM Capacity: 4213.4MB 5.9.
AEC-7763LC/LD & ARS-2022/2022D Press ENT, and LCD will show the comparison information as follows. Compare- DVD 0% 4213.4MB 15:00 When comparison comes to an end, LCD will show the results as follows. Compare Fail: 0 OK: 1 Diff: 0 Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2. If the comparison is identical, LCD will show the message as follows.
AEC-7763LC/LD & ARS-2022/2022D 5.9.5 Select Image This function is to select an image file from a certain partition in the hard drive. First, select the function by pressing ▼. 9-05.Image P: A Select Image After installing a hard drive, ARS-2022D will format it automatically. Each partition occupies 5GB. The number of partitions is dependent on the hard drive’s capacity. The partitions are alphabetically arranged. Select a partition by pressing ENT, and LCD will show the message as follows.
AEC-7763LC/LD & ARS-2022/2022D First, select the function by pressing ▼. 9-06. Image P: A Image Src Drive Then, use ▲ ▼ to select DVD-ROM or DVD writer as the source. Select Img Src: 01 IDE1 DVD-ROM After selecting the source such as DVD-ROM, you can press ENT, and LCD will show the message as follows. Load image from Drive ID-01 5.10 Edit Track (for CD only) Function 10 Edit Track is exclusively designed for editing a collection of favorite songs from CDs.
AEC-7763LC/LD & ARS-2022/2022D Select function 10. 10. Edit Track 5.10.1 CD to CD On the above figure press ENT, and you will enter the following figure.Here the function CD to CD is to let you select a track or more from CD-ROM, and then copy into a blank CD-R/RW. 10-01. Edit Track CD to CD Edit On the above figure press ENT, and you will enter the following figure. Here 1/10 means the number one of the 10 tracks, and 03:25 means the playing time.
AEC-7763LC/LD & ARS-2022/2022D After selecting, please use ▲ to move to the “End” menu as shown below. Select Track: End 1Trk03:25 Press ENT to finish the CD editing, and use ▲ ▼ to confirm Yes or No. End edit disc and burn?Yes LCD will show the copying information as follows. Copying- 24X Edit 1/10 - > 1/1 On the above figure 1/1 means the first track of all tracks we have selected, and here we have just selected one track. When copying comes to an end, LCD will show the message as follows.
AEC-7763LC/LD & ARS-2022/2022D If you want to keep editing, the current source CD will eject auctomatically, and the system will ask you to insert another new CD as shown below. Insert next disc After inserting the new CD, press ENT to edit as before. Suppose we decide to select the second track, then press ENT. A “+” will appear beside 2/10 as shown below. Select Track: +2/10 04:25 After selecting, please use ▲ to move to the “End” menu as shown below.
AEC-7763LC/LD & ARS-2022/2022D On the above figure 2/2 means the second track of all tracks we have selected, and so far we have selected two tracks from two different CDs. When copying comes to an end, LCD will show the message as follows. Burn Complete! OK: 01 The system will ask if you want to keep editing. Suppose we don’t like to continue, then press ▼ to confirm No. Continue edit next Disc?No On the above figure Press ENT. The system will ask if you want to close all CDs’ sessions.
AEC-7763LC/LD & ARS-2022/2022D 5.10.2 CD to HDD After closing sessions, press ESC and ▼ to enter the following figure.Here the function CD to HDD is to let you select a track or more from CD-ROM, and then copy into a certain partition of HDD. 10-02. Edit Track CD to HDD Edit On the above figure press ENT, and you will enter the following figure. Here 1/10 means the number one of the 10 tracks, and 03:25 means the playing time.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to finish the CD editing, and use ▲ ▼ to confirm Yes or No. End edit disc and burn?Yes Then, the track as an image file will be loaded into HDD. LCD will show the loading information as follows. Load- P0 -24X Edit 1/10 - > 1/1 When loading comes to an end, LCD will show the message as follows. Image load OK The system will ask if you want to keep editing. Please use ▲ ▼ to confirm Yes or No as shown below.
AEC-7763LC/LD & ARS-2022/2022D After inserting the new CD, press ENT to edit as before. Suppose we select the second track, then press ENT. A “+” will appear beside 2/10 as shown below. Select Track: +2/10 04:25 After selecting, please use ▲ to move to the “End” menu as shown below. Select Track: End 1Trk04:25 Press ENT to finish the CD editing, and use ▲ ▼ to confirm Yes or No. End edit disc and burn?Yes Then, the track as an image file will be loaded into HDD.
AEC-7763LC/LD & ARS-2022/2022D The system will ask if you want to keep editing. This time please use ▼ to confirm No as shown below. Continue edit next Disc?No Then, the system will ask if you want to burn from HDD into CD-R/RW or move into a partition. Please use ▲ to confirm Burn as shown below. Burn or Move to partition?Burn After pressing ▲ , LCD will show the copying information as follows. Copy- P0 -24X 0% 1/2 Trk03:25 When burning finishes, LCD will show the results as follows.
AEC-7763LC/LD & ARS-2022/2022D After pressing ▼, you need to select a partition into which the data will be moved. Suppose we select A as shown below. Select Partition A After pressing ENT, LCD will show the moving information as follows. Moving to P: A 0% When moving finishes, LCD will show the results as follows. Moving to P: A OK! If the chosen partition has contained image data, the system will ask to overwrite or keep the data. Here please use ▲ to overwrite.
AEC-7763LC/LD & ARS-2022/2022D When moving finishes, LCD will show the results as follows. Moving to P: A OK! 5.10.3 Play Audio Track This function is to make ARS-2022D act as a music player. You can plug an AV terminal in the audio port on the back of the device, and enjoy the music. On the above figure press ESC and ▼ to select the function. 10-03. Edit Track Play Audio Track Use ▲ ▼ to select the track you want to play.
AEC-7763LC/LD & ARS-2022/2022D On the above figure press ESC and ▼ to select the function. 10-04. Edit Track Close Session After pressing ENT, the system will ask if you are sure to close. Close all disc’s session? Yes After pressing ENT, LCD will show the message as follows. Closing Session Please wait--- When closing finishes, LCD will show the results as follows. Closing OK :1 Complete Fail :0 5.11 Setup Function 11 Setup lets you change the default settings.
AEC-7763LC/LD & ARS-2022/2022D Select function 11. 11. Setup 5.11.1 Language On the above figure press ENT, and you will enter the following figure. The function Language lets you select a language in which messages can be shown on LCD. 11-01. Setup Language Press ENT to enter the following figure. Here the LCD only supports English. Japanese, Traditional Chinese and Simplified Chinese are optional. Language English 5.11.2 CD Burn Speed On the above figure press ESC and ▼ to enter the following figure.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the following figure. The default is auto. CD Burn Speed Auto 5.11.3 DVD Burn Speed On the above figure press ESC and ▼ to enter the following figure. The function DVD Burn Speed lets you control the burning speed of DVD writer. 11-03. Setup DVD Burn Speed Press ENT to enter the following figure. The default is maximum. DVD Burn Speed Maximum 5.11.4 Read Speed On the above figure press ESC and ▼ to enter the following figure.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the following figure. The default is maximum, but there are still other choices: 32X, 16X and 8X. Read Speed Maximum 5.11.5 Auto Start Drive On the above figure press ESC and ▼ to enter the following figure. Auto Start Drive is to copy or test automatically once you put a blank DVD onto the writer. 11-05. Setup Auto Start Drive Press ENT to enter the following figure. The default is Off. Press ▼ to select 1 (one blank DVD). Auto Start Drive Off 5.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the following figure. The default is Copy. Of course you can select any other function as the first item, but remember to press ENT. Startup Menu 1.Copy 5.11.7 Auto Verify On the above figure press ESC and ▼ to enter the following figure. Auto Verify is to verify automatically if the target DVD can be read after copying. 11-07. Setup Auto Verify Press ENT to enter the following figure. The default is Off. Press ▼ to select On. Auto Verify Off 5.11.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the following figure. The default is Off. Press ▼ to select On. Auto Compare Off 5.11.9 Auto Prescan On the above figure press ESC and ▼ to enter the following figure. Auto Prescan is to scan automatically if the source DVD can be read correctly, and by the way to test the reading speed. 11-09. Setup Auto Prescan Press ENT to enter the following figure. The default is Off. Press ▼ to select On. Auto Prescan Off 5.11.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the following figure. The default is Eject Good Only. Press ▼ to select Eject All Disc or Do Not Eject. Eject Disc Eject Good Only 5.11.11 Burn On The Fly On the above figure press ESC and ▼ to enter the following figure. Burn On The Fly lets you control the copying methods. When the setting is On, the data will be copied directly from the source DVD to the target DVD.
AEC-7763LC/LD & ARS-2022/2022D 5.11.12 Burn Mode On the above figure press ESC to return to Function 11, and then select part 12 Burn Mode as the following figure shows. Burn Mode lets you control the burning modes. There are two modes: DAO (Disc At Once) and TAO (Track At Once). They support CD only. If the DVD writer doesn’t support the mode you have selected, ARS-2022D will automatically switch to another mode. 11-12. Setup Burn Mode Press ENT to enter the next figure. The default is DAO.
AEC-7763LC/LD & ARS-2022/2022D 5.11.14 Device Info On the above figure press ESC and ▼ to enter the following figure. Device Info shows the basic information of the DVD-ROM and DVD writer you have installed. 11-14. Setup Device Info Press ENT to enter the next figure. 01 IDE1 Master DVD-ROM : PIONEER Press ENT to enter the next figure. DVD-ROM 1.22 Press DVD-116 ▼ twice to enter the next figure. 02 IDE2 Master DVD-RW : PIONEER Press ENT to enter the next figure. DVD-RW DVR-103 1.
AEC-7763LC/LD & ARS-2022/2022D 5.11.15 System Info On the above figure press ESC and ▼ to enter the following figure. System Info shows the information of the system. 11-15. Setup System Info Press ENT to enter the next figure. DVD Duplicator 1-1 ver: 1.54L Press ENT to enter the next figure. WINBOND: W29C040 2002 / 5 / 27 ACARD 5.11.16 Quick Erase On the above figure press ESC and ▼ to enter the following figure. Quick Erase is to erase the data on the DVD rewriteable disk quickly. 11-16.
AEC-7763LC/LD & ARS-2022/2022D After confirming Yes and pressing ENT, LCD will show the message as follows. Erasing disc 00:00 (Quick) When erasing finishes, LCD will show the results as follows. Quick Erase OK:01 Fail:00 5.11.17 Full Erase On the above figure press ESC and ▼ to enter the following figure. Full Erase is to erase the data on the DVD rewriteable disk completely. Compared with Quick Erase, Full Erase takes longer time to do the job. 11-17.
AEC-7763LC/LD & ARS-2022/2022D When erasing finishes, LCD will show the results as follows. Full Erase OK:01 Fail:00 5.12 Adv Setup Function 12 Adv Setup lets you change the system configuration. This function includes 12 parts. They are UnderRun Protect, Overburn, Read Error Skip, Format HDD, Verify HDD, Burn-in, Update Firmware, Compare Firmware, H/W Diagnostic, Load Default, CD+G, and ISRC. On the above figure press ESC to return to Function 11.
AEC-7763LC/LD & ARS-2022/2022D UnderRun Protect lets you control On and Off of Buffer Under Run Protection such as Burn Proof, SafeBurn, JustLink, Seamless Link, etc. Press ENT to enter the following figure. The default is On. Press ▼ to select Off. UnderRun Protect On 5.12.2 Overburn On the above figure press ESC and ▼ to enter the following figure. Overburn lets you decide whether to copy beyond the limit of the CD or not. 12-02. Adv Setup Overburn Press ENT to enter the following figure.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the following figure. The default is Off. Press ▼ to select On. Read Error Skip Off 5.12.4 Format HDD On the above figure press ESC and ▼ to enter the next figure. Format HDD is to partition the hard drive. But before formatting all data on the hard drive will be deleted. 12-04. Adv Setup Format HDD Press ENT to get the next figure. In DVD a partition occupies 5GB while in CD 1GB.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the next figure. Use ▲ ▼ to confirm Disk or Parti. Verify Disk or Partition? Disk Press ENT to verify. After verification LCD will show the results as follows. Verify Hard Disk OK! 5.12.6 Burn-in On the above figure press ESC and ▼ to enter the following figure. Burn-in is to simulate the copying progress many times. The time can be from 1 to 1000.
AEC-7763LC/LD & ARS-2022/2022D Press ESC, ENT, ▼ to select Erase & Copy as the following figure shows. Erase & Copy is to erase and write repeatedly. It is only for DVD rewriteable disk. Burn-in Erase&Copy Press ENT and use ▲ ▼ to select the time of simulation such as 1, 2, 3...1000 or Run Continuous. The figure below shows Run Continuous. Sel burn-in num: Run Continuous 5.12.7 Update Firmware On the above figure press ESC and ▼ to enter the following figure.
AEC-7763LC/LD & ARS-2022/2022D 5.12.8 Compare Firmware On the above figure press ESC and ▼ to enter the following figure.Compare Firmware is to compare the current firmware version and the newly downloaded version. It can prove if the downloaded version is the newest one. 12-08. Adv Setup Compare Firmware 5.12.9 H/W Diagnostic Press ESC and ▼ to enter the next figure. H/W Diagnostic is to test the system. 12-09. Adv Setup H/W Diagnostic Press ENT to enter the next figure.
AEC-7763LC/LD & ARS-2022/2022D 5.12.10 Load Default On the above figure press ESC and ▼ to enter the next figure. Load Default is to make all changed settings recover to defaults. 12-10. Adv Setup Load Default Press ENT to enter the next figure. Use ▲ ▼ to confirm Yes or No. Load Default Config? Yes When default loading finishes, LCD will show the results as follows. Load Default OK 5.12.11 CD+G On the above figure press ESC and ▼ to enter the following figure.
AEC-7763LC/LD & ARS-2022/2022D Press ENT to enter the next figure. The default is Off. Press ▼ to select On. CD+G Off 5.12.12 ISRC & MCN On the above figure press ESC and ▼ to enter the following figure. ISRC and MCN are special copying formats. This function supports them. 12-12. Adv Setup ISRC & MCN Press ENT to enter the next figure. The default is Off. Press ISRC & MCN Off 48 ▼ to select On.
AEC-7763LC/LD & ARS-2022/2022D Chapter 6 Troubleshooting 6.1 About LCD After powering on if there is no LCD, please check if the connection of power cord is frim and the environment of power outlet is normal. 6.2 About Error Messages During Copy, Test, Compare and Verify, etc. if you press ESC to abort, an error message will appear on LCD. Abortion may cause ARS-2022D to hang up, therefore you have to power on again. If reading fails, an error message will appear on LCD.
AEC-7763LC/LD & ARS-2022/2022D 6.4 About Buttons If you press any one of the four buttons on the panel, but there is no response, it is perhaps that the button cannot function well. Please inspect the jumper setting. 6.5 About DVD Writer Not Readable After copying if the DVD writer is unreadable, please use Compare to examine, or get another DVD-ROM to test. 6.6 About High Failure Rate If the failure rate of copying is high, please do the following things to improve.
AEC-7763LC/LD & ARS-2022/2022D 6.8 About Function 12 and Cancellation If you want to execute function 12 Advanced Setup, you can press ESC for 2 seconds. And during operation if you want to cancel a function like Copy, Test, Verify and so on, you can press ESC for 2 seconds, too.
AEC-7763LC/LD & ARS-2022/2022D Appendix 1 List of Functions 1 Copy 2 Test 3 Test & Copy 4 Verify 5 Compare 6 Prescan 7 Disc Info 8 Select Source 9 Image (It works only when a hard disk is connected) 9.1 Load 9.2 Delete Image 9.3 Image Info 9.4 Compare Image 9.5 Select Image 9.6 Select Src Drive 10 Edit Track (for CD only) 10.1 CD to CD 10.2 CD to HDD (It works only when a hard disk is connected) 10.3 Play Audio Track 10.4 Close Session 11 Setup 11.1 Language (English) 11.
AEC-7763LC/LD & ARS-2022/2022D 11.11 Burn On The Fly (Default is On) 11.12 Burn Mode (Default is DAO) 11.13 Button Sound (Default is On) 11.14 Device Info 11.15 System Info 11.16 Quick Erase 11.17 Full Erase 12 Adv Setup 12.1 UnderRun Protect (Default is On) 12.2 Overburn (Default is Off) 12.3 Read Error Skip (Default is Off) 12.4 Format HDD 12.5 Verify HDD 12.6 Burn-in 12.7 Update Firmware 12.8 Compare Firmware 12.9 H/W Diagnostic 12.10 Load Default 12.11 CD+G (Default is Off) 12.
AEC-7763LC/LD & ARS-2022/2022D Appendix 2 LCD Messages 1. Normal Conditions: Initialize SDRAM............................................Initialize the memory of the system. Detect Drives..............................Detect what drives are connected with the system. User Abort!.............................................................Cancel the job during operation. Analyzing............................................................................Analyze the source disc. Source Drive Not Ready.......
AEC-7763LC/LD & ARS-2022/2022D Press a Key to Eject Good Disc... Press any ket to eject the good disc after copying Press a Key to Eject Fail Disc......Press any key to eject the failed disc after copying. DVD-RW does not Support the Func.......... DVD-RW doesn’t support this function. Hold ESC to exit................................ Press ESC for a second to terminate the test. All data will be lost, erase?.........All data on the disc will be lost. Confirm the erasing of data. Erase Finished..............
AEC-7763LC/LD & ARS-2022/2022D Verify Hard Disk OK!................................... The hard disk is verified successfully. Verify Hard Disk Fail!............................ The hard disk is not verified successfully. Verify Partition Header!.................................................. Verify the partition header. Select HD First!................................................ Select a formatted hard disk at first. 3. Audio Editing: Lost selected Tracks?................................
AEC-7763LC/LD & ARS-2022/2022D Update F/W xxx to yyy?...... Do you want to update the firmware version from xxx to yyy? Searching F/W ................................... The system is searching for a valid firmware. Check Sum Error!.................................................. The udpated firmware has errors. Source can’t be Hard Disk!......During comparison the source cannot be hard disk. Last update F/W OK!................................... The firmware is updated successfully.
AEC-7763LC/LD & ARS-2022/2022D Technical Support Form Email: support@acard.com http://www.acard.