User manual Bluetooth Headset
English English 1. Check phone compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Charge Jabra BT250v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Read the glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. “Pair” to your Bluetooth™ phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Unplug the AC adaptor from the charging cradle. English 1 Blue Indicator Light 1 2 Multi-Function Button 2 3 Volume Control Button 4 Charging Cradle 5 MiniGel™ 6. Remove the headset from the charging cradle. You are now ready to “pair” Jabra BT250v to your mobile phone. If the headset has already been paired to your phone, then you can begin using it. WARNING: Do not attempt to charge Jabra BT250v with anything other than the AC adaptor provided.
1. To turn off the vibrate feature, hold the volume-down button while you turn the headset on. “Pair” to your Bluetooth phone English Pairing3 will create a unique and encrypted wireless link between two Bluetooth enabled devices such as your Bluetooth phone and Jabra BT250v. 2. If you wish to re-activate the vibrate feature, hold the volume-up button while you turn the headset on. 1. Ensure the headset is off (see Turning headset on/off section). BASIC OPERATIONS 2.
7 9 • • Choosing wearing preference Press and release once OR End call from phone’s keypad 10 Jabra BT250v is ready to wear on the right ear. If you prefer the left, gently rotate the MiniGel 180°. • For optimal performance, wear Jabra BT250v and your Bluetooth phone on the same side of your body. In general, you will get better performance when there are no obstructions (including parts of your body) between the headset and the phone. • Fig.
English 12 Resetting the headset If the headset is not responding or the blue light will not turn on or off after pairing, you may need to RESET your headset. 1. Fully insert the headset into the charging cradle. 2. Plug the Jabra BT250v AC adaptor into the headset’s charging cradle. 3. Plug the AC adaptor into the electrical outlet. 4. Leave the headset in the charging cradle for about 3 seconds, then remove the headset (see Fig. 1). 5. Unplug the AC adaptor from the charging cradle.
English • Last number redial (when not on a call) While the headset is on, press and hold until you hear 2 short beeps, release immediately • Rejecting an incoming call (when not on a call) When your phone rings, press and hold until you hear 2 short beeps, release immediately • Call-waiting (swapping between 2 calls) When your phone notifies you of another incoming call while you’re on a call, press and hold until you hear 2 short beeps, release immediately • Putting a call on hold While you’re on
Certification and safety approvals English This product is CE marked according to the provisions of the R & TTE Directive (99/5/EC). Hereby, GN Netcom, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further information please consult http://www.gnnetcom.com Please note that this product uses radio frequency bands not harmonised within EU.
© 2004 GN Netcom A/S. All rights reserved. Jabra is a registered trademark, wholly owned by GN Netcom Inc., and MiniGels is a trademark of GN Netcom Inc. in the USA, and these trademarks may be registered in other countries. US and foreign patents pending. Design and specifications subject to change without notice. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by the companies in the GN Netcom Group is under license. www.jabra.