Owners manual

ManualsBrandsGO RHINO ManualsAutomotiveGo Rhino 28173T BR20 Rear Replacement Bumper

REV. DATE: 4/8/2016 Page 1 of 6

Parts List

Item

Qty.

Part #

Description

Item

Qty.

Part #

Description

Torque

28173T0AB

Bumper Replacement Shell

AST-T131

½” x 1 ½ ” Hex Bolt

65 ft. lbs.

28173T0DB

Driver Side Frame Bracket

AST-T226

½” x 2” Hex bolt

65 ft. lbs.

28173T0DB

Passenger Side Frame Bracket

AST-RP06

½” Flat Washer

28173T5AB

Flush Mount Light Pod Plate

AST-RPR06

½” Lock Washer

ASE-L01

LED License Plate Light

AST-TU05

½” Hex Nut

28173T5GA

Sensor Bezel Plate (inner)

AST-T766

10-32 x ¾” Button Head Bolt

30 in. lbs.

28173T5FA

Sensor Bezel Plate (passenger outer)

AST-TU297

10-32 Nylon-Insert Lock Nut

28173T5FA

Sensor Bezel Plate (driver outer)

ASP-T4A2

Round Plug

ASP-T4A3

Rectangular Plug

Installation Instructions

BR20 Rear Bumper Replacement Part # 28173T

2015-2016 Chevrolet Silverado 2500HD & 3500HD 2/4WD

Do not attempt to install this product on any vehicle other than the one listed above!

DAKAR PRO Brackets Part

# 524765

2014 Chevrolet Silverado 1500 2/4WD

Do not attempt to install this product on any vehicle other than the one listed above!

Tool Required:

13mm, 15mm, 18mm, 21mm, 3/8” & 3/4” Sockets

13mm, 15mm, 18mm, 21mm. 3/8” & 3/4” Wrenches

Slotted Blade Screw Driver

1/8” Hex Key

Ratchet, Ratchet Extensions & Swivel Joint Adapter

12V Circuit Tester

Approximate installation time: 90 min

ILLUSTRATION #1

Summary of content (6 pages)

PAGE 1
Installation Instructions BR20 Rear Bumper Replacement Part # 28173T 2015-2016 Chevrolet Silverado 2500HD & 3500HD 2/4WD Do not attempt to install this product on any vehicle other than the one listed above! Parts List Item Qty. Part # 1 1 28173T0AB 2 1 3 1 4 2 5 2 28173T5AB ASE-L01 6 2 28173T5GA 7 1 8 1 28173T0DB Description Item DAKAR PRO Brackets Part Qty.
PAGE 2
Important Installation Notes and Suggestions To maintain and care this product keep it clean and do not use abrasive cleaners or polish waxes. Texture Painted Finish: Mild liquid detergent may be used. Polished Stainless & Semi-Gloss Painted Finishes: We recommend using only non-abrasive automotive wax such as pure carnauba to avoid scratches and rust.
PAGE 3
Step-7 Loosen the M12 bolts (2) per side toward the end of the frame securing the bed, (Photo 5 & 6). #6 Driver Side #5 Driver Side Step-8 Remove the M10 bolt (1) per side and M14 bolts (2) per side securing the bumper brackets to the frame, (Photo 7). Step-9 With assistance, remove the factory bumper and brackets by slightly lifting the bed off the frame, and pulling the bumper rearward away from the vehicle, (Photo 8).
PAGE 4
Step-1 If the vehicle is equipped with rear Park Assist, remove each sensor from the bezel by gently spreading the bezel tabs and pulling out on the back of the sensors. Note: Do not push on the front of the sensor as this may damage the sensor. Step 2 Remove the sensor bezels from the factory bumper by depressing the (4) tabs around the base and pushing the bezel out through the front of the bumper.
PAGE 5
Step-7 Position the driver side frame bracket inside the frame rail and secure the frame bracket and receiver hitch to the bottom of the frame using (1) ½” x 2” hex bolt and to the side of the frame using (2) ½” x 1 ½” hex bolts, (6) ½” flat washers, (3) ½” lock washers and (3) ½” Hex nuts, (Photo 5 & 6). Tighten the nuts and bolts. Repeat to install the passenger side frame bracket.
PAGE 6
Step-10 Remove the trailer plug from the factory bumper and install it in the bumper shell, and reconnect the wiring harness, (Photo 9 & 10). #9 Driver Side #10 Driver Side Step-11 Install the license plate using the supplied LED lights and fasteners to the bumper shell. Use a circuit tester to find the hot and ground from the factory license plate light wiring, and then splice the wires from the supplied lights.