Owners manual

Tools requiered:
Instructions:
Cleaning and care instructions:
Revised 20/DIC/2007
G:\Usuarios\Diseño\Instructivos PDF\37S\37246-i.Pdf
INSTALLATION INSTRUCTIONS
PART#4923(B-C-PS)
08-13 JEEP LIBERTY 2&4WD (sport excluded)
(1) Hardware kit 37246:
(2) 3/8" Bolt plate
Parts List:
QTY
(1) Set Side bars
(1) Set front brackets
(1) Set rear brackets
(4) Auxiliary brackets
(2) 1/2" Bolt plate
(6) 3/8" Lock washer zinc plated
Ratchet
(6) 3/8" Flat washer
(4) 3/8" Rod bolt
9/16" Socket
(12) 3/8" Flat washer black
(4) 3/8" x 1 1/4"Carriage head bolt
(8) 3/8" Lock washer black
(4) 3/8" Hex. lock nut black
9/16" Wrench
3/4" Socket
3/4" Wrench
Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish, or
wax that contains an abrasive is detrimental to the finish, as the compounds scratch the finish and cause corrosion.
Diseño: Calidad:
(6) 3/8" Hex. Nut
(1) 3/8" Bolt guide
(2) 1/2" Lock washer
(2) 1/2" Flat washer
(2) 1/2" Hex. Nut
(8) 3/8" x 1" Hex. Head bolt black
Aproximated installation time: 45 min.
1. Before beginning the installation, please read the instructions thoroughly and verify that the hardware kit is complete. If any
of the pieces listed above are missing, call you distributor immediately to obtain the necessary items.
2. Identify your product´s components. Tips: The front of the side bar has the step pad farther from the edge and the front
bracket is longer than the rear one. In the front bottom side of the side steps you will find a code, the one ending with 1 is for
the driver side, and the one with 2 is for the passenger side.
Side bar
1/2" Bolt plate
3/8" Bolt plate
Rear Bracket (shorter)
Front Bracket
(longer)
Auxiliary Bracket
3/8" Rod bolt
FRONT
DRIVER SIDE
3. With the help of the 3/8" bolt guide insert the rod bolt inside the chasis through the square hole and take the bolt´s tip out
through the circular hole. See diagram 1. Fix the auxiliary bracket to the chasis with one 3/8" flat washer, one 3/8" lock
washer and one 3/8" nut. Do not tighten yet.
4. Insert the 1/2" bolt plate in the hole shown in diagram 1 and fix the front bracket to the chasis with one 1/2" flat washer,
one 1/2" lock washer and one 1/2" nut. Fix to the auxiliary bracket using one 3/8" carriage head bolt, one 3/8" flat washer and
one 3/8" lock nut. Do not tighten yet.
5. In similar way to described in step 3 fix the auxiliary bracket to the chasis in the rear of vehicle, see diagram 2. Do not
tighten yet.
6. Insert the 3/8" bolt plate in the oval hole shown in diagram 2 and fix the rear bracket using one 3/8" flat washer, one 3/8"
lock washer and one 3/8" nut. Fix to the auxiliary bracket using one 3/8" carriage head bolt, one 3/8" flat washer and one 3/8"
lock nut. Do not tighten yet.
7. Fix the side bar to the brackets using (4) 3/8" bolts, (4) 3/8" flat washers and (4) 3/8" lock washers. Do not tighten yet.
8. Align the side bar and tighten all hardware.
9. Repeat for the other side of vehicle.
10. Fill out the waranty card included and place it inside your vehicle.
1 of 3 FOD
I7.003.I