GET TO KNOW YOUR GEAR HOW TO CHAIN How to Chain We recommend chaining two Nomad 100 Solar Panels in series by inserting one MC4 Connector into the female MC4 Connector of the second panel and then into the recommended adapter cable (see below). Utilizing this method, voltages will increase and amperages will remain the same, causing less electrical friction and heat. When chaining Nomad 100 Solar Panels, you must purchase a MC4 to AP Adapter Cable to plug into the Goal Zero Yeti 1250.
DÉCOUVREZ VOTRE APPAREIL COMMENT ENCHAÎNER Comment enchaîner Nous recommandons d’enchaîner en série deux panneaux solaires Nomad 100 en insérant un connecteur MC4 dans le connecteur femelle MC4 du second panneau, puis dans le câble de l’adaptateur recommandé (voir ci-dessous). Grâce à cette méthode, la tension augmentera sans que l’intensité varie, ce qui diminuera le « frottement électrique » et l’échauffement.
製品概要 接続方法 チェーン接続の方法 2 つの Nomad 100 ソーラーパネルを連結するには、MC4 コネクタを 2 つ目のパネルにあるメスの MC4 コネクタに接続 し、その後推奨品のアダプターケーブルに接続します (下記参照)。 この方法を使用することで、電圧を上げ、 アンペア数を パネル背面にある MC4 コネクタ 均一に保ち、通電摩擦と熱の発生を抑えます。Nomad 100 ソーラーパネルをチェーン接続する場合、Goal Zero Yeti 1250 を接続するために MC4 - AP アダプターケーブルをお買い求めください。 注:チェーン接続された Nomad 100 ソーラーパネルを Goal Zero Yeti 150、Goal Zero Yeti 400 ソーラー発電機、 または Sherpa パワーパックに接続しないようにしてください。2 つ以上の Nomad 100 ソーラーパネルを連結する場合、サード パーティー製 MC4 分岐コネクタをお買い求めください。 別売の延長ケーブル プラス 別売の延長ケーブル マイナス 8mm Goal Zero コネクタ Goal
LERNEN SIE IHR GERÄT KENNEN VERBINDEN SIE IHR GERÄT Verbinden Sie Ihr Gerät Wir empfehlen, zwei Nomad 100 Solarmodule hintereinander zu verbinden, indem ein MC4-Verbinder in die MC4-Buchse des zweiten Moduls gesteckt wird und anschließend in das empfohlene Adapterkabel (siehe unten). Durch dieses Verfahren werden Spannungen erhöht und Stromstärken beibehalten, was zu weniger elektrischer Reibung und Hitze führt.
CONOZCA SU EQUIPO CÓMO ESTABLECER EL ENLACE Cómo establecer el enlace Se recomienda enlazar dos paneles solares Nomad 100 en serie e insertar un conector MC4 en el conector MC4 hembra del segundo panel y luego en el cable adaptador recomendado (ver a continuación). Al utilizar este método, los voltajes se incrementarán y los amperajes seguirán siendo los mismos, lo cual causará menos fricción y calor.
GOAL ZERO HEADQUARTERS 675 West 14600 South Bluffdale, UT 84065 1-888-794-6250 Designed in the U.S.A. Made in China Nomad is a trademark of Goal Zero. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.