User Manual
Table Of Contents
- page0_580R
- page1_580R
- page2_580R
- page3_580R
- page4_580R
- page5_580R
- page6_580R
- page7_580R
- page8_580R
- page9_580R
- page10_580R
- page11_580R
- page12_580R
- page13_580R
- page14_580R
- page15_580R
- page16_580R
- page17_580R
- page18_580R
- page19_580R
- page20_580R
- page21_580R
- page22_580R
- page23_580R
- page24_580R
- page25_580R
- page26_580R
- page27_580R
- page28_580R
- page29_580R
- page30_580R
- page31_580R
- page32_580R
- page33_580R
- page34_580R
- page35_580R
- page36_580R
- page37_580R
- page38_580R
- page39_580R
- page40_580R
- page41_580R
- Sheet1
- Drawing View1
- Drawing View5
- Drawing View6
- Drawing View7
- Drawing View8
- Drawing View15
- Drawing View24
- Drawing View26
- Drawing View28
- Drawing View32
- Drawing View33
- Drawing View37
- Drawing View46
- Drawing View47
- Drawing View48
- Drawing View49
- Drawing View50
- Drawing View52
- Drawing View54
- Drawing View55
- Drawing View56
- Drawing View57
- Drawing View61
- Drawing View65
- Sheet1
- page42_580R
- page43_580R
- Sheet1
- Drawing View48
- Drawing View54
- Drawing View60
- Drawing View61
- Drawing View63
- Drawing View71
- Drawing View79
- Drawing View80
- Drawing View89
- Drawing View90
- Drawing View91
- Drawing View92
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View97
- Drawing View98
- Drawing View100
- Drawing View101
- Drawing View102
- Drawing View104
- Drawing View105
- Sheet1
- page44_580R
- Sheet1
- Drawing View69
- Drawing View74
- Drawing View75
- Drawing View83
- Drawing View86
- Drawing View87
- Drawing View88
- Drawing View89
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View96
- Drawing View97
- Drawing View98
- Drawing View99
- Drawing View100
- Drawing View101
- Drawing View102
- Drawing View103
- Drawing View104
- Drawing View105
- Drawing View106
- Drawing View107
- Drawing View108
- Drawing View109
- Drawing View110
- Drawing View111
- Drawing View112
- Drawing View116
- Drawing View117
- Sheet1
- page45_580R
- Sheet1
- Drawing View8
- Drawing View9
- Drawing View13
- Drawing View14
- Drawing View15
- Drawing View18
- Drawing View19
- Drawing View23
- Drawing View24
- Drawing View25
- Drawing View26
- Drawing View27
- Drawing View29
- Drawing View31
- Drawing View32
- Drawing View34
- Drawing View35
- Drawing View53
- Drawing View54
- Drawing View55
- Drawing View56
- Drawing View64
- Drawing View79
- Drawing View80
- Drawing View81
- Drawing View82
- Drawing View83
- Drawing View84
- Drawing View85
- Drawing View86
- Drawing View87
- Drawing View89
- Drawing View90
- Drawing View91
- Drawing View92
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View97
- Drawing View98
- Drawing View99
- Drawing View104
- Drawing View106
- Drawing View109
- Drawing View110
- Drawing View111
- Drawing View112
- Drawing View113
- Drawing View114
- Sheet1
- page46_580R
- page47_580R
Small ID
Larger ID
Socket Head Cap
Screw M2.5x18mm
(HC032-S)
Uniball M3
(H0065-S)
eg: Microlube
GL261
Box 1, Bag for page 11
LINKAGE ROD
ASSEMBLED
RADIUS ARM
ASSEMBLY
Already assembled
with 2 bearing
UNIBALL RADIUS
ARM ASSEMBLY
CENTER HUB
ASSEMBLY
Blade Grip
(H1368-S)
Washer
11x
13.8x0.5
(HC594-S)
Thrust Bearing
8x
14x4mm
(HC437-S)
Button Head Cap
Screw M6x10mm
(HC122-S)
Washer
6x
12 x1mm
(HC193-S)
Blade Grip Arm
(H1342-S)
Socket Head Cap
Special M4x8mm
(HC582-S)
Socket Head Cap
Screw M2.5x15mm
(HC028-S)
Washer
2.5x
4x0.3mm
(HC172-S)
Bearing
8x
14x4mm
(HC417-S)
NOTE:
It is a normal ( especially with the 90° + 90° O-ring set-up ) to feel tight
after initial assembly as the axial preload is usually high when the
helicopter is brand new. The preload will loosen up after 2-5 flights
allowing the system to become smooth.
Shim
8x
14x0.2mm [HC228-S] [Bag11-4].
After approximately 40/50 flights, please check preload, you can add
one 0.2mm shim (HC228) on each side if preload has changed.
However, we suggest to replace the o-rings after about 100 flights.
Page 11
HEAD ASSEMBLY