User Manual
Table Of Contents
- page1_K.PDF
- page2_K.PDF
- page3_K.PDF
- page4_K.PDF
- page5_K.PDF
- page6_K.PDF
- page7_K.PDF
- page8_K.PDF
- page9_K.PDF
- page10_K.PDF
- page11_K.PDF
- page12_K.PDF
- page13_K.PDF
- page14_K.PDF
- page15_K.PDF
- page16_K.PDF
- page17_K.PDF
- page18_K.PDF
- page19_K.PDF
- page20_K.PDF
- page21_K.PDF
- page22_K.PDF
- page23_K.PDF
- page24_K.PDF
- page25_K.PDF
- page26_K.PDF
- page27_K.PDF
- page28_K.PDF
- page29_K.PDF
- page30_K.PDF
- page31_K.PDF
- page32_K.PDF
- page33_K.PDF
- page34_K.PDF
- page35_K.PDF
- page36_K.PDF
- page37_K.PDF
- page38_K.PDF
- page39_K.PDF
- page40_K.PDF
- page41_K.PDF
- page42_K.PDF
- page43_K.PDF
- page44_K.PDF
- Sheet1
- Drawing View9
- Drawing View10
- Drawing View12
- Drawing View13
- Drawing View15
- Drawing View16
- Drawing View17
- Drawing View20
- Drawing View21
- Drawing View22
- Drawing View24
- Drawing View25
- Drawing View26
- Drawing View27
- Drawing View28
- Drawing View30
- Drawing View31
- Drawing View32
- Drawing View33
- Drawing View34
- Drawing View36
- Drawing View37
- Drawing View38
- Drawing View39
- Drawing View40
- Drawing View41
- Sheet1
- page45_K.PDF
- Sheet1
- Drawing View1
- Drawing View2
- Drawing View4
- Drawing View5
- Drawing View6
- Drawing View7
- Drawing View8
- Drawing View9
- Drawing View10
- Drawing View11
- Drawing View12
- Drawing View13
- Drawing View14
- Drawing View15
- Drawing View16
- Drawing View17
- Drawing View18
- Drawing View19
- Drawing View20
- Drawing View21
- Drawing View22
- Drawing View23
- Drawing View24
- Drawing View25
- Drawing View26
- Drawing View27
- Drawing View28
- Drawing View29
- Drawing View30
- Drawing View31
- Drawing View32
- Drawing View33
- Drawing View34
- Drawing View35
- Drawing View36
- Sheet1
- page46_K.PDF
- Sheet1
- Drawing View37
- Drawing View38
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View42
- Drawing View45
- Drawing View46
- Drawing View56
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View61
- Drawing View63
- Drawing View65
- Drawing View71
- Drawing View73
- Drawing View74
- Drawing View75
- Drawing View78
- Drawing View81
- Drawing View82
- Drawing View83
- Drawing View84
- Drawing View86
- Drawing View87
- Drawing View89
- Drawing View90
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View100
- Drawing View105
- Drawing View110
- Sheet1
Bolt M10
(HC546-S)
Kraken Tail Boom
(H1074-S)
Nut Block
(HC546-S)
Nut M10
(HC546-S)
Boom Block Support
(H1061-S)
Washer
10x
16x0.2mm
(HC232-S)
Foam 1, BAG12
Use this special
tool to apply the
correct torque to
the nuts.
1 2
3 4
Lock the Nut Block
with a small qty of
CA glue
DO NOT over tighten the screw.
Tighten the bolts as tight as
you can with your fingers, then
add 2 quarter turns to finish
tightening them.
Page 18
TAIL BOOM ASSEMBLY