Safety Instructions

(2)(1) (3)
(5) (6) (7)(4)
CONTROL BUTTONS
RADIO LED INDICATORS
VIEW SOFTWARE VERSION NUMBER
1.The intercom and the computer are connected by a data cable.
2.Open the GPS software on the computer, select the
correct port, and click "Online".
3.After successful connection, in the parameter setting
interface, you can view the current software version
number, such as V001.11.
TURN ON / OFF THE RADIO
1.In shutdown mode, press and hold the front switch of the
body for 2 seconds to turn on and broadcast "power on".
2.In pairing mode or connection mode, press and hold the
switch for 5 seconds to turn off and broadcast "power off".
Menu
Up
Down
Lanyard Hole
Light Indicator
Power On/off
Push-to-Talk
Micro USB
Charging Port
Audiojack
Charging
Indicator
Antenna
Standby state Green Slow Flash
Transmit (TX) Solid Red
Receive (RX) Solid Green
Programming Mode (Read from Radio) Red Fast Flash
Programming Mode (Write to Radio) Red Fast Flash
Rev.1
START MANUAL
Walkie-Talkie
+
SAFETY AND GENERAL INFORMATION
RF Exposure and Product Safety Instructions for Portable
Two-Way Radios General Populated and Uncontrolled
Environments.
ATTENTION:
Before using this radio, refer to the important operating
instructions
for safe usage and RF energy awareness and control for
compliance with applicable Standards and Regulations.
Compliance with RF Exposure Standards
Your Two-Way radio complies with the following RF energy
exposure standard and guidelines:
· United States Federal Communications Commission,
Code of Federal Regulations; 47 CFR et seq. & FCC.
· Institute of Electrical and Electronic Engineers (IEEE) C95.1.
· Ministry of Health (Canada) Safety Code 6 & Industry
Canada RSS-102.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver.
To control your exposure and ensure compliance with the
general population /uncontrolled environment exposure
limits, always adhere to the following procedure:
· Transmit no more than 50% of the time.
· To receive calls, release the PTT button.
· To transmit (talk), press the Push-to-Talk (PTT) button in
front of the face.
· Hold the radio in a vertical position with the microphone
(and other parts of the radio including the antenna) at
least one inch (2.5 centimeters) away from the nose or
lips. Keeping the radio at a proper distance is important
to ensure compliance.
Note: RF exposure decreases with increasing
distance from the antenna.
· Body Worn Operation. When worn on the body,
always place the radio in a approved clip for this
product.
Two-way Radio Operation
· Use only approved supplied or replacement antennas
and audio accessories.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and
receiver.
· Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
ISEDC RSS warning
This product meets the applicable Industry Canada
technical specifications. / Le présent matériel est conforme
aux specifications techniques applicables d’Industrie
Canada.
This device complies with ISEDC license-exempt
RSSstandard (s). Operation is subject to the following two
conditions: (1) this device may not cause interference,and
(2) this device must accept any interference,including
interference that may cause undesiredoperation of the
device.
Le présent appareil est conforme aux CNR d'ISEDCapplica-
bles aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditionssuivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
ISEDC Radiation Exposure Statement:
For face up operation, this model device has been tested
and meets the ISED RF exposure guidelines when used
with an accessory designated for this product or when used
with an accessory that Contains no metal and that positions
the handset a minimum of 25mm from the face.
For body worn operation, this model device has been tested
and meets the ISED RF exposure guidelines when used
with an accessory designated for this product or when used
with an accessory that Contains no metal.
Pour une utilisation face vers le haut, ce modèle d'appareil a
été testé et répond aux directives d'exposition RF ISED
lorsqu'il est utilisé avec unaccessoire désigné pour ce
produit ou lorsqu'il est utilisé avec unaccessoire qui ne
contient pas de métal et qui positionne le combiné à au
moins 25 mm du visage.
Pour une utilisation sur le corps, ce modèle d'appareil a été
testé et répond aux directives d'exposition RF de la ISED
lorsqu'il est utilisé avec unaccessoire désigné pour ce
produit ou lorsqu'il est utilisé avec un accessoire qui ne
contient pas de métal.
Any Changes or modi-cations not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
Tout changement ou modi-cation non expressément
approuvé par la partie responsable de la conformité
l'équipement.