Full Product Manual

GD00Z-4
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR
Installation Instructions
➊
PRODUCT DESCRIPTION
➋
SAFETY NOTES
➌
PRODUCT COMPONENTS
➍
TILT SENSOR INSTALLATION AND BATTERY
➎
PAIRING (INCLUDING) WITH THE SYSTEM
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors
only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
Do not install the Remote Command Transceiver on
garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment
detection system).
WARNING
The Remote Command Transceiver must be mounted in
the garage, in sight of the garage door, where the visual
and audible movement warning indicators can be clearly
seen and heard.
GD00Z-4
POWER
INPUT
JACK
WARNING
LIGHT
LINK
BUTTON
CONNECTION
WIRES
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-4
POWER
SUPPLY
TILT
SENSOR
STATUS
INDICATOR
OPTIONAL
ADJUSTABLE
GD00Z-4 MOUNTING
BRACKET
POWER
SUPPLY
RETAINING
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREW FOR
POWER SUPPLY
BRACKET
WIRE
TIES
TO INCLUDE THE GD00Z-4
INTO YOUR CONTROLLER
1
2
WALL
OUTLET
POWER
SUPPLY
POWER
INPUT
JACK
LINK
BUTTON
GD00Z-4
Press and release the link button
on the GD00Z-4.
Note: Plug in the GD00Z-4
near your Z-Wave Controller
for these steps
Place your Z-Wave Controller into
Discovery or Include mode.
TO EXCLUDE THE GD00Z-4
FROM YOUR CONTROLLER
Confirm that the GD00Z-4 was
recognized by your Z-Wave Controller.
Refer to your Z-Wave Controllers
instructions for additional information
on including devices.
3
1
2
Press and release the link button
on the GD00Z-4.
Place your Z-Wave Controller into
Exclude mode.
Confirm that the GD00Z-4 was
excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers
instructions for additional information
on excluding devices.
3
CR2032
PLUS SIDE UP !!!
The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell
Insert the
battery
into the
transmitter
To open the case, twist
a small screwdriver
in case slot
SLOT
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
POST ON
BOTTOM
"UP"
ARROWS
Snap the sensor onto
the mounting plate
To activate the tilt sensor,
remove the battery protection pull strip
2
ARROWS ON PLATE
& SENSOR POINT UP
LOW BATTERY REPLACEMENT
1
2
1
3
Attach the mounting plate
to the top panel of the door
USA & Canada [phone] & [phone]
[phone] - Toll Free FAX [phone]
www.linearcorp.com
GD00Z-4 Overview
• A garage door opener remote
command transceiver with built-in
Z-Wave technology.
• Allows remote operation of a garage
door opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve
communications within the Z-Wave
mesh network.
GD00Z-4 Summary of Operation
• GD00Z-4 connects to the garage door
opener’s pushbutton wall console
terminals.
• A wireless tilt sensor mounts on the
garage door and reports the door’s
position to the GD00Z-4.
• GD00Z-4 responds to Z-Wave
commands from Z-Wave controllers to
open or close the garage door.
• A warning indicator light fl ashes and
a beeper sounds for 5 seconds before
the door begins to move.
• If the door does not completely
open or close, a second open or
close command can be sent after
30 seconds.
• If the door does not completely open
or close after the second attempt,
the GD00Z-4 operation is suspended
until a local garage door pushbutton is
activated.
Z-Wave Information
• Z-Wave
®
is a registered trademark
of Sigma Designs Inc. and/or its
subsidiaries.
• Z-Wave is an Interoperable two-way RF
mesh networking technology designed
for use with a Z-Wave gateway/
controller and other Z-Wave enabled
devices.
• Replication is the process of copying or
transferring your Z-Wave network from
one controller to another.
• This is a Security enabled Z-Wave
product and must be used with a
Security enabled Z-Wave controller
in order to fully utilize this product. As
such, this device will not respond to
Basic CC commands.
• ASSOCIATION: The GD00Z-4 s
upports
1 Group with 1 Node. Group 1 must be
assigned the Node ID of the controller
to which unsolicited notifi cations from
the GD00Z-4 will be sent. The Z-Wave
controller should set this association
automatically after inclusion.