Full Product Manual

ManualsBrandsGoControl ManualsElectricalZ-Wave Garage Door Opener Remote Controller

➏

GD00Z-4 MOUNTING

➐

GD00Z-4 CONNECTIONS

➑

SYSTEM OPERATION

➒

OPERATION NOTES

1. The warning light will ﬂ ash and the warning beeper will sound for ﬁ ve seconds

before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR

OPENER. THEY ARE ABOUT TO MOVE!

2. If the door does not completely open or close after remote activation, the GD00Z-4

will allow user to try to operate the door one more time. If the second attempt fails,

the GD00Z-4 will go into lock-out mode. See Note #3.

3. If the GD00Z-4 is in lock-out mode and will not accept remote commands, activate

the door from the pushbutton wall console.

4. Once the GD00Z-4 has initiated the movement of the garage door, another

command cannot be sent for 30 seconds. This eliminates the chance of “bouncing”

the garage door and possibly damaging the garage door opener.

➓

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Unable to include in

Z-Wave network.

GD00Z-4 was not

properly excluded

from a previous

Z-Wave network.

1. Reset the GD00Z-4 by pressing

the LINK button 5 times. A quick

beep followed by a longer beep

will indicate the reset.

The GD00Z-4 does

not ﬂ ash or beep

when activated.

No power to the

GD00Z-4.

1. Make sure the power supply is

plugged in securely to a live outlet.

2. Make sure the power cord

is plugged in securely to the

GD00Z-4.

The GD00Z-4

ﬂ ashes and beeps

when activated but

the door does not

move.

Obstruction

blocking the door

or incorrect wiring.

1. Make sure that there are no obstacles

preventing the door from moving.

2. Make sure that the GD00Z-4

connection wires are connected

to the proper terminals on the

garage door opener. Trace the

wires from the garage door

opener’s pushbutton wall console

to the door opener. This is where

the GD00Z-4 connection wires

should be connected.

Garage door opens

or closes, but the

status does not

change on the

Z-Wave Controller.

The tilt sensor

signal is not being

received by the

GD00Z-4.

1. Make sure the tilt sensor is

mounted correctly on the garage

door, with the arrow pointing up.

2. Make sure the battery pull tab has

been removed from the tilt sensor.

3. Replace the battery in the tilt sensor.

LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12)

months. This warranty extends only to wholesale customers who buy direct from Linear or

through Linear’s normal distribution channels. Linear does not warrant this product to consumers.

Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any.

There are no obligations or liabilities on the part of Linear LLC for consequential damages

arising out of or in connection with use or performance of this product or other indirect

damages with respect to loss of property, revenue, or proﬁ t, or cost of removal, installation,

or reinstallation. All implied warranties, including implied warranties for merchantability and

implied warranties for ﬁ tness, are valid only until the warranty expires. This Linear LLC Warranty

is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#).

Contact Linear Returns at 1-855-546-3351 for an RPA# and other important details.

REGULATORY NOTICES

This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject

to the following two conditions: (1) This device may not cause harmful interference and (2) this

device must accept any interference received, including interference that may cause undesired

operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil

ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Changes or modiﬁ cations not expressly approved by the manufacturer could void the user’s

authority to operate the equipment.

Les changements ou modiﬁ cations non approuvés expressément par la partie responsable de la

conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.

The GD00Z-4 typically

mounts on the ceiling

near the opener and

the power outlet

Tilt sensor

mounted on

the top panel

of the door

THE GD00Z-4 CAN ALSO BE ATTACHED TO THE OPENER'S

HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET

THE GD00Z-4 WARNING

LAMP MUST BE VISIBLE IN

ALL DOOR POSITIONS

3/16" HOLES

FOR ANCHORS

The optional adjustable

mounting bracket fits

3 ways on the GD00Z-4

The bracket snaps onto

indents on either side or

on the end of the GD00Z-4

Secure

bracket

with screw

Use the four screws

and anchors to mount

the GD00Z-4 above

the opener

INDENT

Use the bolts and nuts supplied

to attach the bracket to a secure

structure

BE SURE THE GD00Z-4

IS CLEAR OF ALL MOVING

PARTS OF THE GARAGE DOOR

AND THE WARNING LAMP IS

NOT OBSTRUCTED

INDENT

REMOVE POWER FROM THE

GARAGE DOOR OPENER

BEFORE CONTINUING

! WARNING !

PUSHBUTTON

GARAGE

DOOR

OPENER

Connect the GD00Z-4 connection

wires to the pushbutton wall console

terminals on the garage door opener.

The terminals may be named "PWC", "WC",

"PB", "PUSHBUTTON", or "RED and WHITE".

Terminal names and locations vary by model.

DO NOT DISCONNECT

ANY WIRES CURRENTLY

CONNECTED TO THE

GARAGE DOOR OPENER !!!

Remove the screw from 120 VAC

outlet faceplate. Secure the retaining

bracket to the faceplate with the provided

screw. Snap the power supply into the

bracket while plugging into the outlet.

USE WIRE TIES TO SECURE

EXCESS WIRING CLEAR

OF ALL MOVING PARTS

OF THE GARAGE

DOOR AND OPENER

Either wire can

connect to either

terminal

Plug the power cord

into the power input

jack on the GD00Z-4

FLASH

BEEP

Use your Z-Wave Controller to

activate your garage door opener

The GD00Z-4 will activate

the door opener and open

or close the door

STAY CLEAR

OF THE DOOR !!!

The GD00Z-4 will beep and

flash for five seconds before

the door moves

Restore power to your

garage door opener

To synchronize the system,

use the garage door opener's

pushbutton to manually open

and close the door

STAY CLEAR

OF THE DOOR !!!

GD00Z-4 Speciﬁ cations

Power Supply: Input: 120 VAC, 0.8 A

Output: 12 VDC, 2 A

Operating Temperature: -4º—122° F (-20º—50° C)

Audible Alarm: 45 db @ 10 feet

Strobe: 360 Lumens

Communications: Z-Wave (908.4 MHz)

Mounting: Screws and anchors to

the ceiling, or bracket to the

opener’s hanging hardware

Tilt Sensor Speciﬁ cations

Power Supply: Type CR2032 Coin Cell Battery

Operating Temperature: -4º—122° F (-20º—50° C)

Battery Life: 24 Months (typical)

Communications: Proprietary 345 MHz

Range: 100” line-of-sight to GD00Z-4

Mounting to Garage Door: Double-sided tape or two

mounting screws

(Speciﬁ cations subject to change without notice)

NOTICE TO USERS IN CALIFORNIA - CR COIN

CELL LITHIUM BATTERY INFORMATION: THIS

PRODUCT CONTAINS A CR COIN CELL LITHIUM

BATTERY WHICH CONTAINS PERCHLORATE

MATERIAL - SPECIAL HANDLING MAY APPLY - SEE

www.dtsc.ca.gov/hazardouswaste/perchlorate

KEEP AWAY FROM SMALL CHILDREN. IF BATTERY

IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO

NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL

OF USED BATTERIES MUST BE MADE IN

ACCORDANCE WITH THE WASTE RECOVERY AND

RECYCLING REGULATIONS IN YOUR AREA.