Installation Manual

ManualsBrandsGoControl ManualsElectricalZ-Wave Plug-in Lamp Dimmer Module

PD300Z-2 PLUG-IN LAMP MODULE

The GoControl

™

family of Z-Wave

certiﬁ ed wireless lighting products

(smart LED ﬁ xtures, bulbs, switches, dimmers, outlets, plug-in modules, and

thermostats) and security devices (alert sounder, motion sensor, and door/

window sensor) bring a new level of intelligent wireless capability to commercial

and residential environments.

The Z-Wave wireless protocol is an international wireless standard for remote

home automation, security and other applications. This product can be included

and operated in any Z-Wave network with other Z-Wave certiﬁ ed devices from

other manufacturers and/or other applications. All non-battery operated nodes

within the network will act as repeaters regardless of vendor to increase

reliability of the network.

GoControl Z-Wave products are easy to install, are Z-Wave certiﬁ ed, and allow

dealers to create an integrated wireless network with nearly limitless expansion

and interoperability with security, energy management, home entertainment,

appliances, and more.

This product supports 40Kbps data transmission. This product can also

be used for network support in systems that stream metadata. An example

might include transmission of information from audio devices such as song

title, artist, and album information to various displays around the home. As part

of a Z-Wave network, the PD300Z-2 will act as a wireless repeater to insure

that commands intended for another device in the network are received. This

is useful when the device would otherwise be out of the radio range of the

wireless controller.

For indoor use only. Retain instructions for future use.

INSTALLATION

Plug this Lamp Module into the wall outlet near the lamp to be controlled, and

plug the lamp into the Lamp Module. Make sure the lamp(s) to be controlled

total no more than 300 watts.

To reduce the risk of electric shock, this product has a grounded type plug that

has a third (grounding) pin. This plug will only ﬁ t into a grounding type power

outlet. If the plug does not ﬁ t into the outlet, contact a qualiﬁ ed electrician to

install the proper outlet. Do not change the plug in any way.

WARNING: Plugging a non-resistive load such as ﬂ orescent lighting or a device

with a motor may result in damage to the Lamp Module and will void the warranty.

✓ NOTE: The grounded outlet on the right side of the module is always

powered and can be used for any other appliance.

Adding to a network:

See the Wireless Controller operating instructions for details to include this

module under the command of the Wireless Controller.

1. Prepare the Controller to include a unit to the network, by adding it to a

group (method of adding a node to the network). Refer to the Controller

instructions.

2. The PD300Z-2 must be in its permanently installed location.

• For NWI Inclusion, press the button on the PD300Z-2 once.

• For classic inclusion, press the button on the PD300Z-2 twice.

3. You should see an indication on your Controller that the “DEVICE WAS

INCLUDED” in the network.

✓ NOTE: If you have trouble adding the PD300Z-2 to a group it may be that

the Home ID and Node ID were not cleared from it after testing. You must

ﬁ rst “RESET UNIT” with your controller to remove it from the network.

Although adding it to a group includes it in the network, removing it from

a group does not remove it from the network. If removed from a group, it

functions only as a repeater.

Removing from a network:

The PD300Z-2 can be removed from the network by the Controller/Gateway.

Refer to the Controller operating instructions for details.

1. Set the Controller into Removal Mode and follow its instruction to delete the

PD300Z-2 from the Controller.

2. Remove the switch by press the button twice.

3. You should see an indication on your Controller that the “device was

removed” from the network.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,PD300Z-2,GO CONTROL; P/N: 10008878 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2

PD300Z-2

Z-Wave Radio Frequency (RF) Controlled 300 Watt, 120 VAC

NWI and Scene Capable, Plug-In Lamp Module, Series 300

NOTE: This unit must be added to the Network only where it will be permanently installed. The proper operation of this node in the

mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” conﬁ gure this unit, then install.

120 VAC

CONTROLLED

OUTLET

120 VAC

ALWAYS ON

OUTLET

OPERATE / PROGRAM

BUTTON

Button Functions

1. Use to include module under the

command of a Controller.

2. Local ON and OFF control of the

connected load (push and release).

3. Local dimming (hold down).

Summary of content (2 pages)

PAGE 1
PRINTER’S INSTRUCTIONS: INSTR,INSTL,PD300Z-2,GO CONTROL; P/N: 10008878 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2 PD300Z-2 Z-Wave Radio Frequency (RF) Controlled 300 Watt, 120 VAC NWI and Scene Capable, Plug-In Lamp Module, Series 300 Button Functions 1. Use to include module under the command of a Controller. 2. Local ON and OFF control of the connected load (push and release). 3. Local dimming (hold down).
PAGE 2
PRINTER’S INSTRUCTIONS: INSTR,INSTL,PD300Z-2,GO CONTROL; P/N: 10008878 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 2 OF 2 BASIC OPERATION REGULATORY INFORMATION The PD300Z-2 is certified to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. Button (Local Control) The button on the PD300Z-2 allows the user to turn ON, OFF, or DIM and BRIGHTEN the load attached to the controlled outlet.