Installation Manual

ManualsBrandsGoControl ManualsElectricalZ-Wave Plug-In Remote On/Off Appliance Module

PS15Z-2 PLUG-IN APPLIANCE MODULE

The GoControl

™

family of Z-Wave

certiﬁ ed wireless lighting products (smart LED

ﬁ xtures, bulbs, switches, dimmers, outlets, plug-in modules, and thermostats) and

security devices (alert sounder, motion sensor, and door/window sensor) bring a new

level of intelligent wireless capability to commercial and residential environments.

The Z-Wave wireless protocol is an international wireless standard for remote home

automation, security and other applications. This product can be included and operated

in any Z-Wave network with other Z-Wave certiﬁ ed devices from other manufacturers

and/or other applications. All non-battery operated nodes within the network will act as

repeaters regardless of vendor to increase reliability of the network.

GoControl Z-Wave products are easy to install, are Z-Wave certiﬁ ed, and allow dealers to

create an integrated wireless network with nearly limitless expansion and interoperability

with security, energy management, home entertainment, appliances, and more.

This product supports 40Kbps data transmission. This product can also be used for

network support in systems that stream metadata. An example might include transmission

of information from audio devices such as song title, artist, and album information to various

displays around the home. As part of a Z-Wave network, the PS15Z-2 will act as a wireless

repeater to insure that commands intended for another device in the network are received.

This is useful when the device would otherwise be out of the radio range of the wireless

controller.

For indoor use only. Retain instructions for future use.

INSTALLATION

Plug this Appliance Module into the wall outlet near the load to be controlled, and plug

the load into the Appliance Module. Make sure the load to be controlled is 15 amps (1800

watts) or less.

To reduce the risk of electric shock, this product has a grounded type plug that has a

third (grounding) pin. This plug will only ﬁ t into a grounding type power outlet. If the plug

does not ﬁ t into the outlet, contact a qualiﬁ ed electrician to install the proper outlet. Do

not change the plug in any way.

✓ NOTE: The grounded outlet on the right side of the module is always powered and

can be used for any other appliance.

Adding to a network:

See the Wireless Controller operating instructions for details to include this module under

the command of the Wireless Controller.

1. Prepare the Controller to include a unit to the network, by adding it to a group

(method of adding a node to the network). Refer to Controller instructions.

2. The PS15Z-2 must be in its permanently installed location. Press the button on the

PS15Z-2 once.

3. You should see an indication on your Controller that the “DEVICE WAS INCLUDED”

in the network.

✓ NOTE: If you have trouble adding the PS15Z-2 to a group it may be that the Home ID

and Node ID were not cleared from it after testing. You must ﬁ rst “RESET UNIT” with

your controller to remove it from the network. Although adding it to a group includes

it in the network, removing it from a group does not remove it from the network. If

removed from a group, it functions only as a repeater.

Removing from a network:

The PS15Z-2 can be removed from the network by the Controller/Gateway. Refer to the

Controller operating instructions for details.

1. Set the Controller into Removal Mode and follow its instruction to delete the PS15Z-2

from the Controller.

2. Remove the switch by pressing the button twice.

3. You should see an indication on your Controller that the “device was removed” from

the network.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,PS15Z-2,GO CONTROL; P/N: 10008859 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2

PS15Z-2

Z-Wave Radio Frequency (RF) Controlled, 120 VAC

15 Amp, Plug-In Appliance Module, Series 300

NOTE: This unit must be added to the Network only where it will be permanently installed. The proper operation of this node in the

mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” conﬁ gure this unit, then install.

OPERATE / PROGRAM

BUTTON

120 VAC

CONTROLLED

OUTLET

120 VAC

ALWAYS ON

OUTLET

Button Functions

1. Use to include module under the

command of a Controller.

2. Local ON and OFF control of the

connected load (push and release).

Summary of content (2 pages)

PAGE 1
PRINTER’S INSTRUCTIONS: INSTR,INSTL,PS15Z-2,GO CONTROL; P/N: 10008859 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2 PS15Z-2 Z-Wave Radio Frequency (RF) Controlled, 120 VAC 15 Amp, Plug-In Appliance Module, Series 300 Button Functions 1. Use to include module under the command of a Controller. 2. Local ON and OFF control of the connected load (push and release).
PAGE 2
PRINTER’S INSTRUCTIONS: INSTR,INSTL,PS15Z-2,GO CONTROL; P/N: 10008859 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 2 OF 2 BASIC OPERATION REGULATORY INFORMATION The PS15Z-2 is certified to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. This device complies with part 15 of the FCC Rules.