P/N.920-031311-01 Edition 1 04.
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Chapter 1- EZ-Viewer Introduction............................................................................ 3 1-1. General Specifications....................................................................................................................... 3 1-2. EZ-Viewer Accessories...................................................................................................................... 4 1-3. EZ-Viewer Hardware.................................................................................
Chapter 1- EZ-Viewer Introduction 1-1.
1-2. EZ-Viewer Accessories EZ-Viewer RS232 Cable CD After unpacking, please check the accessories that come with the package, and store them appropriately. 1. EZ-Viewer 3. CD (including Software/Manual) 2. RS232 Cable 1-3. EZ-Viewer Hardware Please use the following diagrams to identify each EZ-Viewer part. 1. Three bi-color LED lamps Power (green)ΕReady (green)ΕError (red). 2. Back-light Graphic LCD Display 128(W) × 64(H) dot: to show status of the Logo & printer 3.
1-4. Operation of Three keys Pause Key When pressing the Pause key in standby mode, the printer will go into the Pause Mode, and LCD display will indicate “EZ-xxxx Vx.xxx Pause.” At this time, printer won’t be able to receive any command; but when pressing the Pause key once again, the printer will get out of the Pause mode and go back to standby.
Chapter 2- EZ-Viewer Operation 2-1. Power To run EZ-Viewer, two sources of power are considered: 1. Sharing power with the printer through the printer’s RS-232 cable. Normally, EZ-Viewer requires power of 5V DC 170mA. In case a CCD (barcode scanner) is connected, EZ-Viewer’s power requirement would increase (including that of the CCD’s). 2. Using independent 5V 500mA power adapter to connect to the EZ-Viewer DC Jack.
2-4. Start-Up Turn on the printer power, the EZ-Viewer would automatically link to the EZ-1000 / EZ-1000Plus Series (the LCD display would show “Searching). If connection is successful, the LCD display would show the EZ-1000 / EZ-1000Plus Series model type, firmware version, and the printer status. GODEX GODEX EZ-1X00 VX.XXX Ready to print Searching…… 2-5. Label Print with EZ-Viewer (Please use the EZ-Viewer to setting) 1.
7. Press the Pause key to enter print quantity, and then press the Pause key again to print the label. 8. When the print is finished, the GODEX Print quantity: 1 GODEX Print finished LCD would display the messages shown on the right. Then the printer would go back to the standby mode. 9. Press the Cancel key to enter GODEX “Exit keyboard mode?” Then press the Pause key to leave Exit Keyboard Mode ? [ y/n ] keyboard mode and go back to standby mode. 2-6.
5. Press the Enter key to enter, the LCD display would show the file name which is GODEX downloaded onto the printer. 001 FORM NAME: NewFile1 Press Enter to confirm the file selection. Note: Press EZ-Viewer Feed key to select the previous or the next label format. 6. Use the PS2 keyboard to enter the print quantity, and then press the Enter key to print. 7. When print is finished, the LCD would display the GODEX Print quantity: 3 GODEX Print finished message shown on the right. 8.
2-7. Print Serial and Variable Number Label with Keyboard 1. Please refer to section 2-3Ε2-4 for information on the printer and the EZ-Viewer connection, then start-up the printer. 2. Download the label to the printer first (please refer to the GODEX EZ-1X00 appendix 2 for download instructions), then the LCD GODEX Data receiving… VX.XXX Ready to print would display the messages shown on the right. 3. When download is successful, the EZ-Viewer will beep once, and then go back to standby mode. 4.
8. LCD display will show the Variable Number Prompt. Key in the variable data name. (Example: Apple), then press Enter. GODEX GODEX Product Name: _ Product Name: Apple_ GODEX GODEX 9. Use the PS2 keyboard to input the print quantity, then press Enter key again to print.Ζ 12. When the print is finished, the LCD would show the message Print quantity: 3 Print finished shown on the right. 13.
Chapter 3- Setting 3-1. EZ-Viewer Setting Mode In the Setting Mode, changes can be made according to requirement on the printing mode, options, media type, and parallel interface (printer can only go into the Setting Mode when connected to PC by parallel cable, USB cable, or serial cable). 1. Make sure the printer is powered off. 2. Please refer to section 2-3 to connect the EZ-Viewer to the EZ-1000 / EZ-1000Plus. 3.
Default: Gap Paper Black Mark: for label or plain paper with black mark in the back Paper Setup Gap Paper: for labels with liner and gap, or hang tags. The default is set to be gap paper.
3-2. EZ-Viewer Messages LED Light LCD Message Display Power Ready EZ-XXXX ! ! Vx.xxx Self Test Now in Dump Mode Auto Sensing mode EZ-XXXX Pause Print job is cancelled Press feed key to continue print job PROGRAM LOADING LOADING COMPLETE Setting Mode Green Error Printer Beep 1 ! ! 3 ! ! 3 3 ! ! ! ! ! Description EZ-XXXX: printer model; Vx.xxx: current F/W version Printer is in Self-Test Mode. Please refer to page 14 for more information. Printer is in Dump Mode.
3-4. Auto Sensing Printer can automatically detect label (black mark paper) length and record. This way, without setting the print length, the printer can accurately detect the label (black mark) positions. 1. Check if the Moveable Sensor Mark is located at the right sensing position. 2. Power off the printer first, press and hold the Pause key then turn the printer power back on. 3.
3-6. EZ-Viewer Error Messages LCD Message Display LED Message Light Power Ready Print Head is opened ʳ ʳ ʳ ʳ Entering the Cooling Process Error Beep Description Solution 4 beeps Thermal Print Head Re-open Thermal Print Head and ʳ twice not firmly in place. make sure it closes tightly. Thermal Print Head Printer goes back to standby mode ʳ temperature high. after cooling.
Appendix 1 Download Label to the printer. Download the label to the printer by using the QLabel 1. Please refer to section 2-3 to connect the PCΕEZ-1000/EZ-1000Plus and EZ-Viewer, and then start-up the printer. 2. Start QLabel, and then create a label design. 3. Select the menu item “Advance” => “download” => “label” => “Quick download to printer” to download the label. If the “Quick download to printer” is selected, the system would give a name for this graphic automatically.
Appendix 2 Variable and Serial Number Setting 1. Start QLabel, and then create a label design. 2. Click to insert the first text. Click [Insert]-[Variable]-[New Variable] to insert a new variable. 3. Input Variable length and prompt. Example: Length: 10 Prompt: Product Name. 4. QLabel will show the variable prompt.
5. Click number. to insert the second Text. Click [Insert]-[Serial Number]-[New Serial Number] to insert a new serial 6. Input Serial Number data. Example: Start Value: 1ΙInc/dec. Value: +1ΙPrompt: Serial NumberΙMax number of digits: 5 (select range: 1~13) 7. QLabel will show the variable prompt and serial number start value. 8. When label is created, please refer to appendix 1 to download label and see section 2-7 on how to print.
