User Manual

Wireless Control Function
The flash unit is built in with a Wireless Control Port so that you can
wirelessly adjust the power level of the flash and the flash triggering.
To control the flash wirelessly, you need a FT-16 remote control set (on-
camera and on-flash). Insert its receive end into the Wireless Control Port
on the flash and insert the transmit end into the camera hot shoe. Settings
made on the hotshoe-mounted transmit and receive ends will be wirelessly
communicated to the flash. Then you can press the camera shutter
release button to trigger the flash. You can also hold the transmit end at
hand to control your off-camera flash.
● For full instructions on the use of FT series remote control, see
its user manual.
● Turn off the AD200Pro wireless function.
Other Applications
Sync Triggering
The Sync Cord Jack is a Φ3.5mm plug. Insert a trigger plug here and the flash will be fired synchronously with the
camera shutter.
The following table lists the available and unavailable custom functions of this flash.
1. Press the < MENU > button to enter the C.Fn meun.
2. Select the custom function No.
● Turn the Selection Dial to select the custom function No.
3. Change the setting
● Press < SET > button and the Setting No. blinks.
● Turn the Select Dial to set the desired number. Press < SET > button will confirm the settings.
4. Exit C.Fn menu
● Press < MENU > button to exit.
C.Fn: Setting Custom Functions
Settings & Descriptions
ON
OFF
OFF
S1 mode
S2 mode
OFF
Auto standby
without
any operation
Can be triggered
as second curtain
OFF
ON: Trigger 2 times for
1 cycles,
1th flash of trigger.
ON: Trigger 2 times for
1 cycles,
2th flash of trigger.
Display
Not display
OFF
Choose any figure from 01-99
OFF
ON
Restrictions
NO
M mode
NO
M/Multi mode
M mode
M mode
Wireless mode
M non-high-speed mode
Setting Signs
ON
OFF
OFF
S1
S2
OFF
30 min
60 min
90 min
OFF, 0.01~30s
OFF
N1
N2
ON
OFF
OFF
01-99
OFF
ON
Functions
Beeper
S1/S2 mode
selection
Auto standby
Delay flash
Mask
t0.1 display
ID Setting
Stable Color
Temperature Mode
Custom Function Signs
F1
F2
F3
F4
F5
F6
F7
F8
1. Over-Temperature Protection
● To avoid overheating and deteriorating the flash head, do not fire more than 40 continuous flashes in fast
succession at 1/1 full power. After 40 continuous flashes, allow a rest time of at least 10 minutes.
● If you fire more than 40 continuous flashes and then fire more flashes in short intervals, the inner over-
temperature protection function may be activated and make the recycling time over 10 seconds. If this occurs,
allow a rest time of about 10 minutes, and the flash unit will then return to normal.
● When the over-temperature protection is started, is shown on the AV display.
Number of flashes that will activate over-temperature protection:
Protection Function
- 39 - - 40 -
Power Output Level
1/1
1/2+0.7
1/2+0.3
1/2
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
1/64(+0.3,+0.7)
1/128(+0.3,+0.7)
1/256(+0.3,+0.7)
Number of Flashes
Speedlite flash head
40
50
60
75
100
200
300
500
1000
Bare bulb flash head
60
80
100
120
150
200
300
500
1000