User Manual

2. When PROP is displayed, short press the < > Button to enter Percentage mode.
Short press the SET Button and the percentage value is blinking. Turn the Select Dial
to choose the light brightness from 5% to 100%. Short press the SET Button to exit.
1. When OFF is displayed, short press the < > Button to enter PROP mode. Now the
LCD panel shows PROP.
Short press the Modeling Lamp Button to choose the modeling lamp’s mode (OFF,
PROP and percentage); and long press the Modeling Lamp Button to switch on or off
the function that the modeling is off when triggering the flash.
OFF: Modeling lamp is off.
PROP: The modeling lamp's power changes with the flash's power. The bigger power
the flash has, the brighter the modeling lamp is.
Percentage: Adjust the modeling lamp's light brightness manually from 5% to 100%.
Setting:
Modeling lamp will be off automatically after lighting for 4 hours, avoiding overheat due
to long-time lighting when the user is not nearby.
OPERATIONS
Flash Preparation
(To uninstall the standard reflector,
press the release button on the flash
head and turn the standard reflector
counter-clockwise to take it out, as
illustrated in the picture.)
2. Attach the flash unit onto an appropriate light stand. Adjust the mounting bracket for a
good angle and make sure it is tightened and fixed. Use the direction adjusting handle to
adjust the flash to a desired direction. Umbrella input is for different photo umbrellas to
put in.
1. Take down the lamp cover. Install
the modeling lamp and put on the
glass protection cover and the
standard reflector.
Power Connection
Use the power cord to connect the flash to an AC power source and turn on the power
switch.
Modeling Lamp
When there is flammable accessory on the flash unit, do not keep the
modeling lamp on for a long time. It is recommended to cool it down for one
minute after 10 minutes' working.
3. When PROP is displayed, short press the < > Button can back to <OFF> mode.
4. When in NON OFF mode, long press the < > Button for 2 seconds to switch on the
function that the modeling is off when triggering the flash. Now the LCD panel shows
( ). Long press the < > Button again to exit this mode.
Note: If < > is displayed on the LCD panel, the modeling lamp will be auto off
in triggering and recovered to its original state after triggering.
Test Button
Sync Triggering
◆Optic S2 Secondary Unit Setting: Press <S1/S2> button so that this flash can also
function as an optic S2 secondary flash with optic sensor in M manual flash mode. This
is useful when cameras have pre-flash function. With this function, the flash will ignore a
single “preflash” from the main flash and will only fire in response to the second, actual
flash from the main unit.
Slave Trigger Model
◆No optical control: S1 or S2 is not displayed on the LCD panel, indicating the slave
triggering function is shut down.
Select dial decides different power output, satisfying light requirements in different
environment. The power is adjustable freely from 1/32 to 1/1 which will be accordingly
shown on the LCD display. "OF" on the display indicates that the flash triggering function
is turned off. Press the Test button to discharge power when the flash output is adjusted
from high to low.
GR/CH Button
Short press the GR/CH button can adjust the
built-in wireless group. When the group indicator on the LCD panel is blinking, turn the
select dial to change. And long press the GR/CH button can adjust the built-in wireless
channel. When the channel indicator on the LCD panel is blinking, turn the select dial to
change.
Three slave triggering models are available and can be set by pressing slave model
button (6).
◆Optic S1 Secondary Unit Setting: In M manual flash mode, press <S1/S2> button so
that this flash can function as an optic S1 secondary flash with optic sensor. With this
function, the flash will fire synchronously when the main flash fires, the same effect as
that by the use of radio triggers. This helps create multiple lighting effects.
Power Output Control
To fire the flash without taking a picture, press the test button. It can also help adjust the
flash brightness when combined with the select dial. Press the SET button and turn on
the flash to view its version.
The sync cord jack (2) is a Φ3.5mm plug. Insert
a trigger plug here and the flash will be fired
synchronously with the camera shutter.
- 13 - - 14 -