迅丽TTL机顶闪光灯 Thinklite TTL Camera Flash For Olympus/Panasonic INSTRUCTION MANUAL 说 明 手 册 神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd. 中英文双语 / Chinese English Bilingual 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 在使用本产品之前: 请先仔细阅读本手册,以确保您能安全使用。请保存好本手册以备将 邮箱/E-mail: godox@godox.com 来查询参考。 http://www.godox.
Foreword For Your Safety Thank you for purchasing this product. Always keep this product dry. Do not use in rain or in damp conditions. This TT350O camera flash applies to Olympus/Panasonic series This product contains high-voltage electronic parts. Touching the high-voltage circuit inside it may result in electric shock. Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. cameras and is compatible with TTL autoflash.
Contents 25 Foreword 26 For Your Safety 29 Name of Parts Body Control Panel LCD Panel What's in the Box of TT350O? Separately Sold Accessories 31 Attaching to a Camera 32 Power Management 32 Flash Mode: TTL Autoflash FEC (Flash Exposure Compensation) High-Speed Sync Second-Curtain Sync 34 Flash Mode – M: Manual Flash 35 Flash Mode – Multi: Stroboscopic Flash 36 Wireless Flash Shooting: Radio (2.
● LCD Panel Name of Parts (1) TTL Autoflash Zoom : zoom display (Page 42) Focus length (Page 42) TTL : TTL autoflash 01 02 03 08 04 : Flash exposure compensation (Page 33) 05 (2)M Manual Flash Flash exposure compensation amount M : Manual flash 06 09 Manual flash output (3)Multi Flash 07 ● Body Multi : Stroboscopic flash 01. Catchlight Panel 06. LCD Panel 02. Built-in Wide Panel 07. Lock Ring 03. Flash Head 08. Battery Compartment 04. Optic Control Sensor 09.
● What’s 1. Flash unit in the Box of TT350O? 2. Mini stand 3. Protection case 4. Diffuser Power Management 5. Instruction manual ● Separately Sold Accessories The product can be used in combination with the following accessories sold separately, so as to achieve best photography effects: X1T-O wireless flash trigger, Mini softbox, White & Silver reflector, Honeycomb, Color gels, Snoot, etc. Use Power Switch to power the flash unit on (Long press the button for one second) or off.
FEC: Flash Exposure Compensation With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops. It is useful in situations where minor adjusting of the TTL system is needed based on the environment. Setting FEC: MODE ZOOM SYNC 1 SLAVE SET Press the SET Button and the flash exposure compensation amount will be highlighted on the LCD panel. M: Manual Flash The flash output is adjustable from 1/1 full power to 1/128th power in 1/3rd stop increments.
Multi: Stroboscopic Flash With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of a moving subject in a single photograph. You can set the firing frequency (number of flashes per sec. expressed as Hz), the number of flashes, and the flash output. MODE ZOOM MODE SYNC ZOOM SET SLAVE SYNC SLAVE SET 1 2 3 MODE ZOOM SYNC SLAVE SET MODE ZOOM SYNC SLAVE Press button so that is displayed.
Slave Unit Setting ZOOM SYNC 1 SLAVE SET Long Press the button for 2 seconds so that < > is blinking. Turn the Select Dial until the < > is displayed on the LCD panel, which means the slave unit. 2 Slave Unit Setting ● Set the TT350O that to be controlled as the wireless slave unit. (Page 37) ● The slave unit can be set as A/B/C. 3 Check the communication channel ● If the master unit and slave unit(s) are set to a different channel, set them to the same channel.
5. M: Wireless Flash Shooting with Manual Flash Slave/Master Unit's Positioning and Operation Range This describes wireless (multiple shooting) using manual flash. You can shoot with a different flash output setting for each slave unit (firing group). Set all parameters on the master unit. ● Autoflash Shooting with One Slave Unit MODE ZOOM SYNC SLAVE 1 Setting the flash mode to ● Press the Button to set the flash to M mode.
3 Other Applications Bounce Flash By pointing the flash head toward a wall or ceiling, the flash will bounce off the surface before illuminating the subject. This can soften shadows behind the subject for a more natural-looking shot. This is called bounce flash. To set the bounce direction, hold the flash head and turn it to a satisfying angle. -7-90 Push the wide panel back in. ● Push in only the wide panel. ● Follow the same procedures as for bounce flash.
Using the Wide Panel Pull out the wide panel and place it over the flash head as shown. The flash coverage will then be extended to 14 mm. ● The catchlight panel will come out at the same time. Push the catchlight panel back in. ● When pull out the wide panel, the ZOOM will constantly be 14mm. The button will not work. Low Battery Warning If the battery power is low, < > will appear and blink on the LCD panel. Please replace the battery immediately.
Firmware Upgrade • Auto Focus Assist Beam Effective range (approx.) Center: 0.6~4m This flash supports firmware upgrade through the USB port. Update information will be released on our official website. USB connection line is not included in this product. The USB port is a standard Micro USB socket. Common USB connection line is applicable. Periphery: 0.6~2.5m • Power Supply AA batteries Recycle time Ni-MH batteries (recommended) or 2*LR6 alkaline batteries Approx. 0.1-2.
Troubleshooting If there is a problem, refer to this Troubleshooting Guide. The Camera Flash cannot be charged. ● The battery is installed in the wrong direction. →Install the battery in the correct direction. ● The camera flash’s internal battery is exhausted. →If < > appears and blinks on the LCD panel, replace the battery immediately. The Camera Flash does not fire.