TTL 无线引闪器 TTL Wireless Flash Trigger For FUJIFILM 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.
Contents Foreword Thanks for your purchase of this X1T-F TTL wireless flash trigger. 24 Foreword 25 26 27 28 Setting the Transmitter This TTL wireless flash trigger only applies to FUJIFILM cameras. It can also directly control Warning Power Switch flashes which have built-in Godox wireless X system (e.g. TT685F, V860IIF, AD360II, Names of Parts Power Switch of AF Assist Beam AD600, AD600M, QuickerII, etc.).
Names of Parts Warning Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Always keep this product dry. Do not use in rain or in damp conditions. Body Transmitter TEST Trigger Button Keep out of reach of children. Do not use the flash unit in the presence of flammable gas. In certain circumstance, please pay attention to the relevant warnings.
Names of Parts Using the Flash Trigger Transmitter Panel Note: To set ZOOM functions, please open the ZOOM functions on the camera flash.
Setting the Transmitter Setting the Transmitter Power Switch Mode Settings Slide the Power Switch to ON, and the device is on and Status Indicator Lamp will not blink. 1. Short press the Button and the selected group will blink. Click to choose downwardly and double-click to choose upwardly. 2. Short press the Button and the selected groups' modes will be changed by the order of TTL/M/--(-- represents OFF, which means that the current group will not fire flashes in this mode).
Setting the Transmitter [Note 1] Min. refers to the minimum power output value that can be set in M/Multi mode. 1/128 or 1/256 can be set according to C.Fn-05. The minimum power output value is 1/128 and cannot be set to 1/256 for most of camera flashes. However, the value can change to 1/256 when using in combination with Godox strong power flashes e.g. AD600, etc. Multi Flash Group ON/OFF Settings 1. Open the multi flash in the C.Fn Custom Functions (set C.Fn-04 as 1). 2.
Setting the Transmitter Setting the Transmitter group’s setting turns to the maximum(1/1) or the minimum(Min.). If the current group is in the TTL mode, all the other groups which are in the M mode will change their FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop increments, until one of the group’s setting turns to the maximum(3) or the minimum(3). If the current group is in the -- mode (flash off), the amounts will not change. 4.
Setting the Transmitter Double-click the CH Button to turn on/off the modeling lamp of the receive end. Press the TEST Button to turn on the flash trigger. When the Status Indicator Lamp blinks two Custom Functions No. C.Fn-03 C.Fn-04 C.Fn-05 C.Fn-06 C.Fn-07 C.Fn-08 C.
■ SHOE MOUNT FLASH The following options are available when an optional shoe-mounted flash unit is attached and turned on. Sync: Control flash timing. • (1ST CURTAIN): The flash fires immediately after the shutter opens (generally the best choice). • (2ND CURTAIN): The flash fires immediately before the shutter closes. • (AUTO FP(HSS): High-speed sync (compatible units only). The camera automatically engages front-curtain high-speed sync at shutter speeds faster than the flash sync speed.
Setting the Transmitter Setting the Transmitter Selecting the Operation Method Multi Mode (C.FN-04-on) Press the Button for 5 seconds to switch the operation methods (Method Button 1/Method 2). Operation Function Short press (under normal status) Enter CH settings; X1T-F Operation Method 1(by default) (under settings) Confirm and back to normal status TTL/M Mode Button CH/OK Double-click Control the ON/OFF of modeling flash Operation Function Long press for 2 seconds Enter C.
Setting the Transmitter Setting the Transmitter X1T-F Operation Method 2 Multi Mode (C.
Attentions Technical Data 1. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode. 2. Camera shoots but does not focus. Check if the focus mode of the camera or lens is set to MF. If so, set it to AF. 3. Signal disturbance or shooting interference.
Compatible camera models & functions support: Technical Data Model Model Function X1T-F TTL/M Flash X1T-F A B Standard √ √ REAR √ -- C √ √ Others Synchronization delay set Yes (0~10ms，use 100us as the unit) Beep ON/OFF Modeling flash ON/OFF Stroboscopic Flash AF-assist Beam HSS(FP) Standard √ √ √ -√ -Note 1 √ -- Note: 1.X100T do not have second curtain sync (REAR)function. 2.The AF assist beam will light up when the shutter is at low speed(<200).
