TTL 无线引闪器 TTL Wireless Flash Trigger For Sony 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.
Contents 规格参数 其他 闪光灯提示音 ON/OFF 21 Foreword 造型灯 ON/OFF 22 For Your Safety ZOOM设置 可以通过发射器调节闪灯焦距值 24 Names of Parts Power Switch of AF Assist Beam 显示屏 宽屏液晶显示，背光开启或关闭 Body Channel Settings 输出接口 发射器：PC端子输入、输出 Transmitter Panel Mode Settings Battery Group POWER/FEC Settings 固件更新 通过机身上的Micro USB进行固件升级 Installing Batteries Multi Flash Group ON/OFF Settings 记忆功能 设置2秒后的参数会自动记忆，重新开机自动恢复 Low Battery Level Indication Multi Flash Parameter Setting 发射器尺寸/净重 72x75x52(mm)/90g Using the Flas
For Your Safety Foreword Thanks for your purchase of this X1T-S TTL wireless flash trigger. This TTL wireless flash trigger only applies to SONY cameras. It can also directly control flashes which have built-in Godox wireless X system (e.g. TT685S, V860IIS, AD360II, AD600, AD600M, QuickerII, etc.). As to the flashes which do not have Godox wireless X system (e.g.V860, V850, AD360, etc.), a XTR-16 or XTR-16S receiver can be used in combination to achieve manual flash control.
Names of Parts For Your Safety extremely high temperature. Failure to observe this precaution could result in fire or Body damage to the casing or internal parts. Transmitter Observe precautions when handling batteries TEST Trigger Button Batteries may leak or explode if improperly handled. Observe the following precautions when handling batteries for use in this device: Use only batteries listed in this manual.
Names of Parts Using the Flash Trigger Transmitter Panel Note: To set ZOOM functions, please open the ZOOM functions on the camera flash.
Setting the Transmitter Setting the Transmitter Power Switch Mode Settings Slide the Power Switch to ON, and the device is on and Status Indicator Lamp will not blink. 1. Short press the Button and the selected group will blink. Click to choose downwardly and double-click to choose upwardly. 2. Short press the Button and the selected groups' modes will be changed by the order of TTL/M/--(-- represents OFF, which means that the current group will not fire flashes in this mode).
Setting the Transmitter [Note 1] Min. refers to the minimum power output value that can be set in M/Multi mode. 1/128 or 1/256 can be set according to C.Fn-05. The minimum power output value is 1/128 and cannot be set to 1/256 for most of camera flashes. However, the value can change to 1/256 when using in combination with Godox strong power flashes e.g. AD600, etc. Multi Flash Group ON/OFF Settings 1. Open the multi flash in the C.Fn Custom Functions (set C.Fn-04 as 1). 2.
Setting the Transmitter Setting the Transmitter group’s setting turns to the maximum(1/1) or the minimum(Min.). If the current group is in the TTL mode, all the other groups which are in the M mode will change their FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop increments, until one of the group’s setting turns to the maximum(3) or the minimum(3). If the current group is in the -- mode (flash off), the amounts will not change. 4.
Setting the Transmitter Setting the Transmitter Custom Functions No. Setting the Camera Functions Zoom setting Setting Signs AU Settings and Description Changing with camera's Zoom value. Flashes' auto zoom functions should be turned on. C.Fn-02 To trigger X1T-S, please set camera's flash mode to fill flash, auto flash, slow flash or rear curtain flash. Flash Mode 20,24,28,35,50,70, Zoom（20/24/28/35/50/70/80/105/135/200 mm) Flash Mode Wireless Fill -flash 80,105,135,200 C.
Setting the Transmitter Setting the Transmitter Selecting the Operation Method Multi Mode (C.FN-04-on) Press the Button for 5 seconds to switch the operation methods (Method Button 1/Method 2). Operation Function Short press (under normal status) Enter CH settings; X1T-S Operation Method 1(by default) (under settings) Confirm and back to normal status TTL/M Mode Button CH/OK Double-click Control the ON/OFF of modeling flash Operation Function Long press for 2 seconds Enter C.
Setting the Transmitter Setting the Transmitter X1T-S Operation Method 2 Multi Mode (C.
Attentions Technical Data 1. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode. 2. Camera shoots but does not focus. Check if the focus mode of the camera or lens is set to MF. If so, set it to AF. 3. Signal disturbance or shooting interference.
Technical Data Model X1T-S Others Synchronization delay set Yes (0~10ms，use 100us as the unit) Beep ON/OFF Modeling flash ON/OFF ZOOM setting Adjust the flash's focal length through the transmitter Output interface Transmitter: use a PC cord to input and output Firmware upgrade Use the Micro USB port to upgrade Memory function Settings will be stored for 2 seconds after last operation and recover after a restart Dimension/Weight for Transmitter 72x75x52(mm)/90g Compatible Camera Models Thi
