TTL 无线引闪器 TTL Wireless Flash Trigger 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd. 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 Instruction Manual 邮箱/E-mail: godox@godox.
Contents 24 Foreword Foreword Mode Settings 25 Warning Magnification Function 26 Names of Parts Output Value Settings Body Flash Exposure Compensation LCD Panel 28 Settings Battery Multi Flash Settings Installing Batteries (Output Value, Times Battery Level Indication 28 and Frequency) Using the Flash Trigger Modeling Lamp Settings As a Wireless Camera Flash Trigger ZOOM Value Settings As a Wireless Outdoor Flash Trigger Shutter Sync Settings As a Wireless Original Flash Trigger B
Warning Names of Parts Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Always keep this product dry. Do not use in rain or in damp conditions. Keep out of reach of children. Do not use the flash unit in the presence of flammable gas. In certain circumstance, please pay attention to the relevant warnings. Do not leave or store the product if the ambient temperature reads over 50℃.
Battery Names of Parts AA alkaline batteries are recommended. Installing Batteries As shown in the illustration, slide the battery compartment lid of the flash trigger and insert two AA batteries separately. Battery Indication Check the battery level indication on the LCD panel to see the remaining battery level during the usage.
Using the Flash Trigger 1.2 Long press the button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”). 1.3 Turn on the camera flash, press the < > wireless setting button and the < > wireless icon and slave unit icon will be displayed on the LCD panel.
Using the Flash Trigger Using the Flash Trigger 4. As a Wireless Studio Flash Trigger Take GS400II as an example: 4.1 Turn off the camera and mount the transmitter on camera hotshoe. Then, power on the flash trigger and the camera. 4.2 Long press the button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”). 4.3 Connect the studio flash to power source and power it on.
Using the Flash Trigger 6. As a Flash Trigger with 2.5mm Sync Cord Jack Operation method: 6.1 The connection method please refers to the contents of “As a Wireless Studio Flash Trigger” and “As a Wireless Shutter Release”. 6.2 Press the shutter normally and the flashes will be controlled by sync cord jack’s signal. Setting the Flash Trigger Power Switch Slide the Power Switch to ON, and the device is on and status indicator lamp will not reveal.
Setting the Flash Trigger Setting the Flash Trigger Wireless ID Settings Magnification Function Change the wireless channels and wireless ID to avoid interference for it can only be triggered after the wireless IDs and channels of the master unit and the slave unit are set to the same. Switch between multi-group and one-group mode: choose a group in multi-group mode button to back to multi-group. Press the
Setting the Flash Trigger Setting the Flash Trigger Flash Exposure Compensation Settings 6. Until all the amounts are set. Or during any value setting, short press the button to exit the setting status. No values will blink. 1. Multi-group displays in the TTL mode 1.1 Press the group button to choose the group, turn the select dial, and the FEC value will change from -3 to ~3 in 0.3 stop increments. Press the button 7.
Setting the Flash Trigger Setting the Flash Trigger ZOOM Value Settings Sync Socket Settings Short press the button and the ZOOM value will CH1 be displayed on the LCD panel. Choose the group and turn the button again to back to the main menu. A B C D E Note: The flash’s ZOOM should be set to Auto (A) mode before Zm/CH SYNC the select dial, and the ZOOM value will change from AUTO/24 to 200. Choose the desired value and long press 1. Press the
Setting the Flash Trigger Setting the Flash Trigger SHOOT Function Settings C.Fn: Setting Custom Functions Press the
Setting the Flash Trigger Compatible Flash Models Custom Function Function Setting Signs Settings and Description SHOOT One-shoot Only send triggering signals in the M & Multi mode when camera is shooting Full-shoot Compatible Flash Models Transmitter Receiver Flash XProC -- Send parameters and triggering signal when camera V860II series/V850II/TT685 series is shooting(suitable for multi person photography) APP APP TT600/TT350C Only send triggering signal when camera is shooting QuickerII se
Compatible Flash Models Technical Data The relationship of XT wireless system and X1 wireless system: XT-16 (Code Switch) ON ON ON ON ON ON ON Model XProC Compatible cameras Canon EOS cameras (E-TTL II autoflash) ON Support for the cameras that have PC sync socket.
Attentions Technical Data Model XProC Firmware upgrade Upgrade through the Type-C USB port Memory function Settings will be stored 2 seconds after last operation and As the products needs to do firmware upgrade, please refer to instruction manual recover after a restart Wireless Flash Transmission range (approx.) 0-100m Built-in wireless 2.
