x2 HDMI CAT Splitter/ Extender 4K30 - 70M User's Guide P/N:HD14Ext-2P G4-0143A
Thank you for purchasing from gofanco. Our products aim to meet all your connectivity needs wherever you go. For optimum performance and safety, please read the instructions carefully and keep this User's Guide for future reference. If you need more information about our products, please visit www.gofanco.com. For technical support, email us at support@gofanco.com. For drivers or manual download, please go to www.gofanco.com/downloads.
Introduction The 1x2 HDMI CAT Splitter/Extender distributes HDMI signals from one source device to two CAT6/7 outputs and one HDMI output (loopout). Features • • • • • • • Extends HDMI transmissions up to 70m (230ft) @1080p & 131ft (40m) @4K30Hz HDCP 1.
Package Contents • • • • • • • • • 4 1x 1x2 HDMI CAT Transmitter 2x CAT6/7 Receivers 1x IR Emitter cable 2x IR Receiver cables 1x TX power adapter (5V/1A) 2x RX power adapters (5V/500mA) Surface mount accessories 1x Terminal block (RS232) User guide
Product Layout Figure 1: Transmitter Layout 1. 2. 3. 4. 5. 6. 7. 8. 9.
Product Layout Continued Figure 2: Receiver Front Panel Layout 1. 2. 3. 4. 5.
Product Layout Continued Figure 3: Receiver Back Panel Layout 6. 7. 8. Power Jack: Connects to the included 5V/500mA power adapter 3.
Hardware Installation 1. 2. 3. 4. 5. 6. 7. 8. 8 Power off all devices including your HDMI source and HDMI display(s). Connect your HDMI source device to the Transmitter's HDMI In connector with an HDMI cable (HDMI cable is not included). Connect your CAT cables between the Transmitter and CAT6/7 Receivers. Optional: Connect an HDMI display to the HDMI Out connector of the Transmitter using an HDMI cable (HDMI cable not included).
Application Diagram The application diagram shows the most typical input and output devices used with the Splitter/Extender. Figure 4: Application Diagram CAT Cable Wiring We suggest both RJ-45 connectors be wired identically using T568B wiring standard for the best performance and compatibility.
IR Control Provides IR control of the connected devices. The IR feature is bi-directional so either the source device or the display device(s) can be remotely controlled. Controlling the Source Device 1. Connect an IR Emitter Cable to the IR Out port of the Transmitter. 2. Point the IR Emitter Cable's IR eye in line with the source device's IR window. 3. Connect an IR Receiver Cable to the IR In port on each CAT6/7 Receiver.
RS232 Control Connect the Transmitter's RS232 port to your control PC's serial port using an RS232 cable.
FAQ & Troubleshooting Q: Poor video quality or no video signal on display: A1: Check whether the HDMI cables are connected properly and are in good working condition. A2: Make sure the resolution of the display is compatible with the splitter's resolution Q: No HDMI signal output from the CAT6/7 connectors while the local HDMI out port is working normally: A1: Check whether the HDMI cables are connected properly and are in good working condition. A2: Press the reset button on both TX and RX and reconnect.
Specifications 13
Blank Page 14
Disclaimer The product name and brand name may be registered trademarks of related manufacturers. TM and ® may be omitted on the user's guide. The pictures on the user's guide are just for reference, and there may be some slight differences with the actual products. We reserve the right to make changes without prior notice to a product or system described herein to improve reliability, function, or design.
Thank you for choosing gofanco www.gofanco.
