4x4 HDMI 2.
Thank you for purchasing from gofanco. Our products aim to meet all your connectivity needs wherever you go. For optimum performance and safety, please read the instructions carefully and keep this User's Guide for future reference. If you need more information about our products, please visit www.gofanco.com. For technical support, email us at support@gofanco.com. For drivers or manual download, please go to www.gofanco.com/downloads.
Introduction The 4x4 HDMI 2.0 Matrix LT allows you to connect up to four HDMI source devices and independently switch any source to any of the four HDMI displays. Features • • • • • • Supports up to 4K@60Hz YUV 4:4:4 8-bit, HDR (at 4K@60Hz YUV 4:2:0 10-bit), HDMI 2.0, HDCP 2.2/ 1.4, 18Gbps Supports HD digital audio, LPCM 7.
Product Layout Figure 1: Front Panel Layout 1. 2. 3. 4. 5. 6. 7.
Figure 2: Rear Panel Layout 1. 2. 3. HDMI In (1-4): Connect to your HDMI sources HDMI Out (1-4): Connect to your HDMI displays Power Jack: Connects to the included power adapter Hardware Installation 1. 2. 3. 4. 5. Power off all devices including your HDMI source(s) and HDMI display(s). Connect your HDMI source devices to the Matrix's HDMI In connectors with HDMI cables (HDMI cables not included).
Application Diagram The application diagram shows the most typical input and output devices used with the 4x4 HDMI 2.0 Matrix LT.
Matrix Device Control Remote Control Users can control the 4x4 HDMI 2.0 Matrix LT using the included IR remote. Point the remote control towards the Matrix's IR In window located on the front panel. 1. 2. 3. 4. Standby: Press to place the Matrix into standby mode. Press again to wake up the Matrix Mute: Turns audio On/Off. Choose the output first, then press M.
5. 6. 7. 8. 9. 10. All: Selects one input device to display on all outputs. Example: Press All button, then press Input 1/2/3/ 4 (see # 8) PTP (Port to Port): Press to assign all inputs and outputs to their numerical counterparts. Examples: Input 1 to Output 1, Input 2 to Output 2, Input 3 to Output 3, Input 4 to Output 4 X: Turn off output port. Example: To turn off display on Output 1 - Press Output 1 button (see #4), then press X.
EDID Management Allows you to choose the EDID for each input. Supports built-in and EDID copy modes. There are 8 EDID groups. EDID Table EDID Configuration Mode Setup The Matrix's default EDID is 4K@60Hz YUV 4:4:4 8-bit 2ch (0,0,0,1). Do Not make any changes if the default EDID works properly. 1. 2. To change the EDID for Input 1, long press the HDMI Out 1 Select button (on the Matrix's front panel) for 1 second to enter EDID configuration mode.
3. 4. Long press the HDMI Out 1 Select button for about 1 second or wait 10 seconds to save your changes and exit EDID mode. Repeat steps 1-3 for each HDMI input if necessary. Specifications 10 HDMI Compliance HDMI 2.0 HDCP Compliance HDCP 2.2/1.4 Resolution 480p@60Hz, 576p@50Hz, 720p@60Hz, 1080p@24/50/60Hz, 4K@24/30Hz, 4K@60Hz YUV 4:2:0, 4K@60Hz YUV 4:4:4 Bandwidth 18Gbps Input Video Signal 0.5 - 1.
Disclaimer The product name and brand name may be registered trademarks of related manufacturers. TM and ® may be omitted on the user's guide. The pictures on the user's guide are just for reference, and there may be some slight differences with the actual products. We reserve the right to make changes without prior notice to a product or system described herein to improve reliability, function, or design.
Thank you for choosing gofanco www.gofanco.
