Instruction Manual

ManualsBrandsGold Light Toys Factory ManualsCamera & PhotoDrone Mach 10inch With Camera Streaming

CHOKING HAZARD –

SMALL PARTS NOT FOR CHILDREN UNDER 3 YEARS.

ADULT ASSEMBLY REQUIRED.

Page i

INTRODUCTION

SPECIFICATIONS

Remote Controller Battery: 6 x 1.5V AA

Charging Time: Approximately 100 minutes

Drone Battery: 650 mAh Li-po

Maximum Recommended Altitude 120 ft.

TABLE OF CONTENTS

General Warnings Page 1

Contents and Remote Battery Installation Page 2

Charging Battery and Replacing Propellers Page 3

Remote Overview Page 4

Operating Drone Page 5

Modes Page 6

Tips and FCC Warning Page 7

Page 1

PLEASE RECYCLE OR

DISPOSE OF ELECTRONICS

PROPERLY RECYCLING

INFORMATION IS AVAILABLE AT

WWW.MERCHSOURCE.COM

READ ALL WARNINGS AND PRECAUTIONS BEFORE USE.

Page 2

CONTENTS

REMOTE BATTERY INFORMATION

1. Slide open battery compartment

2. Install 6 “AA” batteries as shown in diagram

shown above

3. Replace and close battery compartment

LITHIUM-POLYMER BATTERY WARNING

BATTERY WARNING

KEEP THE PACKAGE FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION

KEEP THIS INSTRUCTION MANUAL FOR REFERENCE

Page 3

CHARGING BATTERY

Turn off the drone before charging.

Connect the Battery Charge Cable to the charging

port on the Drone.

Connect connector to power source.

Page 4

Page 5

OPERATING DRONE

INSTALLING PHONE HOLDER

Page 6 Page 7

VIDEO STREAMING DRONE VIDEO STREAMING DRONE VIDEO STREAMING DRONE

14+

Congratulations on your purchase of

the Streaming 2.4 GHz Video Drone.

Get ready to soar to new heights.

Master the art of drone flying with

remote control maneuverability. This

lightweight drone will provide hours of

fun.

• Do not mix old and new batteries

• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries

• Insert batteries using the correct polarity. Do not short-circuit the supply terminal

• Only use manufacturer speciﬁed batter(ies), charger(s), and/or adapters, if

applicable, speciﬁed by the manufacturer

• Always use, replace, and recharge (if applicable) batteries under adult supervision

Note: The Battery Charge Cable will light up

when it is charging the battery and turn off when

the battery is fully charged. Charge time is

approximately 100 minutes.

Step 6 – Operating Drone in Flight

The drones range is approximately 250 feet or 120 feet of altitude:

• Read and be aware of all warnings found on Page 1.

• Maintain your desired elevation by using the Throttle.

• Push the Throttle joystick to right or left to spin the drone.

• Use the right joystick to move forward backwards, and side

to side.

• Review step 5 if your drone begins to drift.

• Drone will begin to blink when drone is paired to remote

and battery is low.

Step 5 – Drone Begins to Drift

Follow this step if your drone begins to drift while take off or during

flight.

• Drone drifts backwards: Press the forward Direction Trim

Button.

• Drone drifts forwards: Press the Backwards Direction Trim

Button.

• Drone drifts left: Press the Right Direction Trim Button.

• Drone drifts right: Press the Left Direction Trim Button.

• Drone spins clockwise (viewing drone from top): Press the

Left Spin Trim Button

• Drone spins counter-clockwise (viewing drone from top):

Press the Right Spin Trim Button

Step 7 – Landing Drone

There are two ways to land the drone:

1. Press the Auto Land Button. The drone will slowly begin to land. If

the drone begins to drift, you can still control the drone’s

direction using the Multi Directional Button.

2. Slowly and carefully press the Throttle Joystick down until drone

lands. If the drone begins to drift, you can still control the drone’s

direction using the Multi Directional Button.

Step 2 – Choosing a location

• Drone is designed to be flown indoors and

outdoors.

• Always make sure you have enough space to fly

drone.

• Always follow warnings, page 1.

Step 3 – Starting Drone

1. Making sure your remote is off, slide drone switch

to ON. Drone lights will begin to flicker.

2. Place drone on a flat even surface with clearance

according to diagram (Fig 1).

3. Turn remote on. Make sure the left stick (throttle)

is in a neutral position (stick is centered).

4. Push the stick up and then down.

5. A single tone indicates that the drone is paired.

Drone lights will flicker rapidly then turn on

permanently once paired.

6. If pairing is unsuccessful, repeat steps 3-4.

Step 4 – Lift Off

Slowly and carefully press the Throttle Joystick up.

Drone will begin to elevate. You can compensate for

some of the drones drifting by using the Multi

Directional Button or by following Step 5. You may

need to practice this step several times before

successfully getting drone into the air.

MODES

Auto Orientation Button

• Auto Orientation default setting is off. To enter this mode press Auto Orientation button. Remote will beep twice.

• After drone is successfully paired, the 2 white LED lights toward orientation will be the original forward orientation, when drone is

in auto orientation mode, the drone will orient to the user (remote), no matter what direction the drone is facing. Pushing the right

stick up will send the drone away from the user, pushing it to the right will move the drone right, etc.

• Remote will beep every 6 seconds to indicate the drone is in Auto Orientation mode.

• To exit mode, press the Auto Orientation button. Remote will sound 1 long beep indicating that it has exited Auto

Orientation mode.

Note: Auto Orientation mode is oriented to the user when pairing. If the remote is moved after pairing Auto Orientation, please

follow directions above to reset Auto Orientation.

Auto Landing Button

• Make sure you have achieved level, balanced flight, where the drone is neither climbing nor descending.This mode allows you

to safely and slowly land your drone without having to control the speed. It is done for you automatically.

• The ideal auto landing height is 25-30 ft.

• Press the Land button to trigger auto land. Remote will beep continuously until you exit the auto land mode.

• To steer the drone during landing, use the right control until drone has reached the ground.

• Press the Land button again to exit auto landing mode.

NOTE: Please make sure the throttle joystick is in the down position before exiting auto landing mode

Camera – taking pictures and creating videos

• Taking a picture- press camera icon on app once to take a picture.

• Creating video- press video icon on app once to take a video. Press the video icon on app again to stop recording.

Always turn off remote prior to retrieving

or picking up drone. This will help you

avoid accidently activating propellers.

Connect the Charging

Cable to the Drone

Insert the

Charging Cable

into a

power source

Video Drone

Drone Controller

Charge Cable with

55cm (21.6inch) length

Replacement

Propellors

There is a risk of fire and personal injury if Li-Po

battery is punctured, damaged or misused

• Never expose battery to extreme temperatures

or moisture

• Do not subject battery to strong impacts

• Always keep battery away from flammable

materials

• Only use manufacturer specified batter(ies),

charger(s), and/or adapters, if applicable,

specified by the manufacturer

• Battery is not serviceable

• Let battery cool to room temperature before

charging

• While charging, never leave battery unattended

• Recycle or dispose of battery according to federal,

state and local laws

Step 1 – Pre Flight Checklist

1. Read all warnings and instructions.

2. Install remote batteries, page 2.

3. Make sure that drone and remote are powered off.

4. Install drone holder.

5. Charge batteries, page 3.

SAFETY WARNINGS:

• Not recommended for children under 14 years of age. As with all electrical products, precaution

should be observed during handling and use to reduce the risk of electrical shock.

• Adult supervision is required at all times.

• Before each use, an adult should review the product and battery to determine that no damage

or hazards exist.

• DO NOT TOUCH SPINNING PROPELLERS.

• Do not allow anything to intentionally make contact in any way with spinning propellers.

• Prevent contact with spinning blades by turning off remote prior to handling drone.

• Use caution and pay attention to your surroundings while operating drone.

• Do not fly drone into animals, people, or inanimate objects.

• Keep drone away from power lines, buildings, trees, public areas, and any other potentially

hazardous areas.

• Do not operate in rain, heavy wind, and or any type of severe weather.

• Do not land drone on wet surfaces.

• Never touch or allow others to touch drone while it is flying.

• Always turn drone off when it is not in use.

• Always fly drone in large open areas.

• Never fly drones above or near people, sudden changes in wind or other conditions could lead to

unexpected crashes.

• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and

property rights of others.

• The drone shall never be modified or used for anything except its intended purpose.

TIPS

• Do not crash drone into sand or dirt. Drone gears may become clogged

• When first learning to fly, practice lifting off and hovering

• Stay several feet from walls and buildings

• Always press throttle all the way down after crashing or when something gets stuck in propellers

• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.

• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others.

• The drone shall never be modified or used for anything except its intended purpose.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

TROUBLESHOOTING:

When remote switch is turned on, the remote light does not illuminate:

1) Check that batteries in the remote are installed correctly OR

2) Replace with new batteries

During drone flight, the remote LED is flashing:

1) Remote batteries are low; replace them with new batteries

Drone and remote properly pair, but the drone will not lift-off:

1) Drone battery needs charging. Use the USB Charge Cable to connect the drone to

power source.

After trimming the drone, the drone flight is very unstable and cannot fly properly:

1) One or more blades are most likely damaged;

2) Turn off the drone and remote.

3) Replace with the proper number replacement blade and try flying again.

After impact, the drone is unstable:

1) Put the left remote control lever to the left bottom and put the right remote control lever

to the right bottom at the same time. This will reset the gyroscope (Fig. 1).

2) If the above does not resolve the issue, reboot the drone and controller and pair again.

Remote Controller and Drone can not be paired:

1) Check Point: Remote Controller must be closed to Drone, not exceed 12 feet.

Note: If there are 2 sets of Drones within 12 feet for Pairing, you must pair one successfully before pairing the second set.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

The artwork and design of this package are protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without prior written

permission. Altering, removing or reproducing any of the trademark or copyright notices on this package is not permitted.

China Patent No. ZL201730677298.4

PATENT PENDING

Printed in China

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Invasion of Privacy Warning

Always be mindful of others privacy and do not

record video or take images of others without

their consent. Check and comply with your

federal, state and local laws regarding privacy.

Replacing Propellers

1. Follow diagram

2. Remove screw from top of Propeller

3. Remove broken Propeller and replace

with new Propeller

4. Make sure you installed the correct

blade. Each blade has a number

written on it. Match the blades with

the corresponding number on the

drone

5. Insert screw into top of Propeller

Pairing Drone - First Time

1. Press the connect to Wi-Fi

button

2. Follow the on screen

instructions

After Connecting Drone

1. Press the Stream Button to

begin streaming

2. Press the Album Button to

review pictures and videos

DRONE APP

Go to your app store on your smart phone and download the “360-M Flight” application.

10 FEET

5 FEET

10 FEET

Smart Phone

Mount

GETTING TO KNOW YOUR DRONE

PLEASE READ ALL WARNINGS AND INSTRUCTIONS

PRIOR TO USE. KEEP THIS DOCUMENT AS IT CONTAINS

IMPORTANT INFORMATION ABOUT YOUR DRONE.

2. PAIRING

Before each flight pair the remote with the drone:

1. Turn your drone on and place on a flat, level surface

2. Turn on the remote on and move the left joystick up, then down

3. The beep will indicate successful pairing

4. Repeat steps 1 and 2 if necessary

3. DIRECTIONAL LIGHTS

• White lights indicate the front of the drone

• Red lights indicate the back of the drone

• Not applicable in auto-orientation mode

4. REMOTE CONTROL OVERVIEW

Practice flying your drone below 10 feet and at low speeds until comfortable with all

controls to avoid damage or injury

• Left joystick:

• Up/Down controls elevation

• Left/Right controls spin

• Right joystick: controls flight direction

• Direction Trim: use to eliminate drift

To cut power to drone, move left joystick to down position

1. CHARGING

• Drone must be charged before each use (USB Charge Cable included)

• Indicator light will turn off once fully charged

• Install batteries in remote

CUSTOMER SERVICE

(800) 374-2744

QUESTIONS OR CONCERNS?

PLEASE GIVE US A CALL ... WE’RE HERE TO HELP

Before calling please locate the 10-digit

code printed on the back of your remote

CUSTOMER SERVICE

(800) 374-2744

Insert antena through hole at the base of the

Smart Phone Mount.

Align hole on Mount with hole in antena. Insert

screw to secure Mount to remote.

Carefully slide phone into Mount by pulling up

on top of Mount. Adjust angle accordingly.

Fig. 1

v.06

(Fig. 1)

LAND

SPRINT

TRIM

AUTO

ORIENTATION

DIRECTION

TRIM

OFF

100

LAND

SPRINT

TRIM

AUTO

ORIENTATION

DIRECTION

TRIM

OFF

Light indicates

remote is on

Auto orientation

Auto land

Spin trim

ON/OFF

remote switch

Controls

flight direction

Throttle Joystick

Increases or decreases

drone elevation

Spins drone

LAND

SPRINT

TRIM

AUTO

ORIENTATION

DIRECTION

TRIM

OFF

Forward/

Backwards

Adjustment: Slide

up to adjust forward

and slide down to

adjust backwards

Side to Side

Adjustment:

Slide left to

adjust to the

left and slide

right to

adjust to the

right

FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the drone at least

20cm from nearby persons.

VR ViewerVR Viewer

Take Photos

Flip Camera View

Record Video

View Album

Live Streaming Options