www.workoutwarehouse.com Model No. GGTL58608.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are missing, DO NOT CONTACT THE STORE; please contact Customer Care. IMPORTANT: You must note the product model number and serial number (see the drawing above) before contacting us: 1-877-776-4777 CALL TOLL-FREE: Mon.–Fri. 6 a.m.–6 p.m.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.
24. Inspect and properly tighten all parts of the treadmill regularly. 20. Never leave the treadmill unattended while it is running. Always remove the key, unplug the power cord, and switch the reset/off circuit breaker to the off position when the treadmill is not in use. (See the drawing on page 5 for the location of the circuit breaker.) 25. 21. Do not attempt to raise, lower, or move the treadmill until it is properly assembled.
BEFORE YOU BEGIN Thank you for selecting the revolutionary GOLDʼS GYM MAXX™ TRAINER 685 treadmill. The TRAINER 685 treadmill offers an impressive array of features designed to make your workouts at home more enjoyable and effective. And when youʼre not exercising, the unique treadmill can be folded up, requiring less than half the floor space of other treadmills. ual. To help us assist you, note the product model number and serial number before contacting us.
ASSEMBLY To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton.
2. Slide a Front Endcap (80) onto the Base (81). Partially tighten an Endcap Screw (79) into the Front Endcap and the Base. 2 Slide a Wheel Housing (86) onto the Base (81). Attach the Wheel Housing with a 1" Tek Screw (77), a Base Pad (89), and a 1 1/4" Tek Screw (49) as shown. 86 Attach an additional Base Pad (89) to the Base (81) with a 1" Tek Screw (77). 89 89 77 3. With the help of a second person, carefully tip the treadmill onto its right side as shown.
5. With the help of a second person, carefully raise the Left Upright (70) and the Right Upright (not shown) to a vertical position. 5 Locate the Latch Pin Assembly (73). Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Then, insert the pin into the Latch Housing (71), and tighten the knob onto the pin. 73 Knob See steps 2 and 4. Fully tighten the two Endcap Screws (79).
8. Have a second person hold the console assembly near the Pulse Bar (66). Connect the Console Ground Wire (102) on the Pulse Bar to the ground wire from the console assembly. 8 Connect the console wire to the Upright Wire (75). See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and then try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.
11. Lower the Uprights (70, 76) as shown. 11 Start the two indicated Console Screws (67) into the Left and Right Uprights (70, 76) and the console assembly. If necessary, pull back on the console assembly slightly to align the holes in the Uprights with those on the console assembly. Start the other two Console Screws (67) before tightening all four Console Screws; do not overtighten the Console Screws. Start First Console Assembly Start First 67 70 67 76 12. See the inset drawing.
OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT tric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets. Your treadmill features a walking belt coated with highperformance lubricant.
CONSOLE DIAGRAM Key Clip FEATURES OF THE CONSOLE quick program, see page 15. To create your own quick program, see page 16. To use your own quick program, see page 17. To use the information mode, see page 18. The treadmill console offers an impressive array of features designed to help you get the most from your workouts. When you use the manual mode of the console, you can change the speed and incline of the treadmill with the touch of a button.
HOW TO TURN ON THE POWER 3. Start the walking belt. IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room temperature before turning on the power. If you do not do this, the console displays or other electrical components may become damaged. Plug in the power cord (see page 11). Next, locate the reset/off circuit breaker on the treadmill frame near the power cord. Switch the circuit breaker to the reset position.
The Calories/Distance display—This display will show the approximate number of calories you have burned and the distance that you have walked or run during your workout. The display will change from one measurement to the other every few seconds. To measure your heart rate, stand on the foot rails and hold the metal contacts— avoid moving Contacts your hands. When your pulse is detected, the Incline/Pulse display will show one or two dashes and then your heart rate will be shown.
HOW TO USE A PERSONAL TRAINER QUICK PROGRAM During the program, the profile will show your progress (see the drawing above). The flashing segment of the profile represents the current segment of the program. The height of the flashing segment indicates the speed setting for the current segment. At the end of each segment, a series of tones will sound and the next segment of the profile will begin to flash.
4. Follow your progress with the matrix and the displays. Each custom program is divided into one-minute segments. One Current Segment speed setting and one incline setting can be programmed for each segment. The speed setting for the first segment will be shown in the flashing segment of the profile. To program a speed setting and an incline setting for the first segment, simply adjust the speed and incline of the treadmill as desired by pressing the Quick Speed and Power Incline buttons.
HOW TO USE YOUR OWN QUICK PROGRAM profile will begin to flash. If a different speed and incline setting is programmed for the next segment, the speed or incline setting will flash in the display to alert you. 1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 13. The program will continue in this way until the last segment of the profile flashes in the Current Segment column and the last segment ends. The walking belt will then slow to a stop. 2. Select a custom quick programs.
THE INFORMATION MODE An “E” for English miles or an “M” for metric kilometers will appear in the Quick Speed display. Press the Speed increase button to change the unit of measurement. The console features an information mode that keeps track of the total number of miles that the walking belt has moved and the total number of hours that the treadmill has been operated.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, adjust the incline to the lowest position. If you do not do this, you may damage the treadmill when you fold it. Remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. 1. Hold the metal frame firmly in the location shown by the arrow at the right.
HOW TO LOWER THE TREADMILL FOR USE 1. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left and hold it. Pivot the frame downward until the frame is past the latch pin. Frame Latch Knob Open Latch Pin 2. Hold the metal frame firmly with both hands, and lower it to the floor. CAUTION: To decrease the possibility of injury, do not lower the frame by gripping only the plastic foot rails. Do not drop the frame to the floor.
TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If you need further assistance, please see the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 11).
With the help of a second person, carefully raise the Uprights (70, 76) as shown. Carefully pivot the Hood (28) off. Locate the Reed Switch (39) and the Magnet (6) on the left side of the Pulley (7). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the Screw (11), move the Reed Switch slightly, and then retighten the Screw.
PROBLEM: The walking belt is off-center or slips when walked on SOLUTION: a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes.
EXERCISE GUIDELINES WARNING: Before beginning this Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone.
SUGGESTED STRETCHES The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce. 1. Toe Touch Stretch Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Hamstrings, back of knees and back. 1 2. Hamstring Stretch Sit with one leg extended.
PART LIST—Model No. GGTL58608.0 To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual. Key No. Qty.
Key No. Qty. 101 102 103 104 105 1 1 1 1 1 Description Key No. Qty. Console Fan Console Ground Wire Front Roller Nut Rear Roller Incline Motor Wire * * * * – – – – Description 12" Blue Wire, 2F 12" Blue Wire, M/F 22" Red Wire, M/F 20" Black Wire, M/F Note: Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts. *These parts are not illustrated.
2 20 72 19 21 18 2 23 17 22 12 14 2 24 11 1 28 20 16 21 72 11 25 104 10 15 23 18 2 9 17 19 2 8 3 2 5 4 26 2 27 11 7 6 2 11 12 9 5 10 8 1 2 4 2 EXPLODED DRAWING A—Model No. GGTL58608.
EXPLODED DRAWING B—Model No. GGTL58608.
EXPLODED DRAWING C—Model No. GGTL58608.
EXPLODED DRAWING D—Model No. GGTL58608.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual.