Platinum Series 117cm Tower Fan with WiFi Model: GPTF390
General Care and Safety Guide Thank you for choosing this Goldair product. This Goldair appliance has been designed and manufactured to high standards of engineering and with proper use and care, as described in this leaflet, will give you years of useful service. Please read these instructions carefully and keep them for future reference. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
General Care and Safety Guide 20. Never place appliance close to radiant heat source. 21. Never operate in areas where petrol, paint or other flammable liquids are used or stored. 22. Never use the appliance to dry clothes. 23. Never insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the appliance. 24. Never use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water only.
General Care and Safety Guide The remote control supplied with this heater uses a CR2025 coin type battery. DANGER IF SWALLOWED Keep batteries out of reach of children. Swallowing may lead to serious injury or death in as little as 2 hours due to internal burns. If swallowed, go straight to a hospital emergency room. Dispose of used batteries immediately. WARNING! DANGER IF SWALLOWED Keep batteries out of reach of children.
Assembly The base of the tower fan comes in two parts, which fit around the oscillation base. Both parts fit easily together. The back half is the one with cut-outs for the power supply cord. First remove the large plastic nut from the bottom of the main fan body. Attach the front half of the base, aligning the holes in base with the locating lugs in the oscillation base, and leading the power cord through the centre hole.
Operating your Fan Always choose a safe location for the fan, keeping in mind the safety precautions outlined. Ensure all packaging has been removed from the unit before use. This appliance requires no installation, it should be used solely as a portable appliance. WARNING: Keep all objects at least 1 metre from the front, sides and rear of the appliance. IMPORTANT! NEVER COVER THIS APPLIANCE! Place the fan on a dry, level and sturdy surface.
WiFi – Downloading and Setting up APP For WiFi, the APP is supported only on 2.4GHz WiFi channels. Please ensure your phone is 2.4GHz capable. Download Goldair mobile APP • Open the APP Store or Google Play on your mobile phone. • Open “Search” and enter “Goldair" • Click “GET” and begin to download and install. Once downloaded to your phone open the APP Tap REGISTER in the centre of the screen. If you already have an existing account, then you can Log In. Read and agree to the Tuya Mobile Privacy Notice.
WiFi – Downloading and Setting up APP You can either register an email address or a phone number. The APP defaults to email but you just need to tap the “Register by Phone” at top right of the screen to change. Enter you email address or a phone number then press “Get authentication code”.
Pairing APP to Fan Enter the verification code that you will receive by email or text message Next you will be prompted to Set a Password. The password must contain 6 - 20 characters and must be a mix of letters and numbers.
Pairing APP to Fan We recommend allowing the APP to access your location. The next screen looks like the below. From here you can create your own family set up. Once you set up your family name you can then start to load the various devices around your home. After you have loaded your rooms, press done in the top right hand corner.
Pairing APP to Fan Plug the fan into the mains power and make sure the mains power switch is on. On your phone open the Goldair app. Then tap the “+” button at the top right of the screen. Your tower fan should be ready to connect to your smart phone from when you first turn it off. However if this is not the case or if your fan drops off the WiFi signal, press and hold the OSCILLATION button on the fan for 5 seconds until the WiFi symbol starts flashing.
Pairing APP to Fan Choose/confirm which WiFi to connect to. Note: your phone may pick up other WiFi signals (e.g. neighbours) so you will need to choose. XXXXXX Enter your WiFi password The phone will then connect to the fan. Ensure you have a good strong signal from your WiFi router. Note: The WiFi indicator on the fan may go off during this pairing process. Once complete the screen showing “device added successfully” will appear. Rename the fan if desired. Tap “Completed” to continue.
Operating your Fan from the APP When the phone interface shows the addition is successful, and the WIFI indicator on the fan will stop flashing. The fan pairing is complete and the main control screen on your phone will appear showing the fan as OFF. If the phone and fan fail to connect, then you will need to try to connect again as per the above process. POWER Open the “GOLDAIR" APP to select the fan (when using one mobile phone to control multiple fans, you need to select the fan to be operated).
Operating your Fan from the APP MODE There are 4 modes the fan can go into. To select the mode press the Mode icon. NORMAL – this is the standard and default mode of the fan. 3 Speed settings NATURAL – this mode attempts to mimic the outdoor natural wind type of by constantly changing the wind speed. SLEEP – this mode is very similar to natural mode where the wind speed will change every few seconds. CHILD – Fan will run for 3 hours before turning off.
Operating your Fan from the APP TIMER To set the timer, press the settings button in the lower right corner and then press countdown timer. When the fan is ON you can set it to turn OFF after a number of hours (1-12 hours) has elapsed. When the fan is OFF the timer can be set to come on after 1 to 12 hrs. To cancel the timer, touch the timer button again and tap cancel.
Adding Additional Fans The phone will then connect to the fan. Ensure you have a good strong signal from your WiFi router. Note: The WiFi indicator on the fan screen may disappear during this pairing process. Once complete the screen showing the device has been successfully added will appear. Rename the fan if desired. Tap “Done” to continue.
Adding Additional Fans You can rename the fan. Tap the pencil in the top right hand corner of the fan control screen. Click “Device Name” and rename the fan. Example: Bedroom 1, Dining Room etc. and tap save. Alternatively you can add the ‘Device Location” to identify where the fan is. DEVICE SHARING SET UP The person you add will need to have the Goldair APP installed on their phone. Open the “GOLDAIR APP” and tap the pencil in the top right of the screen.
Cleaning The fan requires regular cleaning to ensure trouble free operation. Unplug the fan from the mains supply before cleaning. Use a damp cloth (not wet) to wipe the exterior of the fan to remove dust and dirt. Use a vacuum cleaner to remove dust and fluff from around the grills. Ensure the fan is dry before plugging back into the mains supply. Do not attempt to dismantle the fan. There are no user serviceable parts. For service or repair, contact an authorised electrical service technician.
Two Year Warranty Thank you for purchasing this Goldair Platinum product. Your product is warranted against faults and manufacture when used in normal domestic use for a period of two year. In non-domestic use Goldair limits the voluntary warranty to three months. Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period.
