Installation Guide

Mark the
centerline* of the
track on the wall
using a level.
door height + 1⁄”.
At the track
connecng points
drill ⁄” pilot holes
followed by ⁄”
pilot holes.
FINISHED FLOOR
*The centerline of
the Track is
represented as
Goldberg Brothers Barn Door Hardware sets come with a one-year manufacture’s
warranty
for defective parts under normal installation and use. Warranty is subject to
repair or replacement of defective part/s at manufacture’s discretion and does not include
installation costs. Goldberg Brothers does not warrant the loss of finish at points where
roller is in contact with the track. Goldberg Brothers Barn Door Hardware is sold as a
rustic finished hardware and Goldberg does not warrant the imperfections seen through
the finish in steel parts. It is part of the look.
This document contains proprietary information of Goldberg Brothers, Inc. and its receipt
of possession does not convey any rights to reproduce or disclose its contents, or to
manufacture, use or sell anything it may describe. Reproduction, disclosure, or use
without prior written authorization from Goldberg Brothers, Inc. is strictly forbidden.
303-321-1099
Goldberg Brothers, Inc.
10488 W. Centennial Rd Suite 100
Lileton, CO 80127
See opposite side for door
and hanger installaon.
Li the door and
hang it from the track.
Finish aaching the
track at the
remaining
connecng points.
Connect the
track to the wall
at the end by
the door
opening as
shown in the
diagram.
Using the same
method connect
the opposite
end of the track
to the wall as
shown.
NOTE:
The end of the
track should
extend ⁄” past of
the door opening.
⁄”
Included Hardware
J-strap hangers (2) T-guide (1) Carriage bolts (4) Washers (6) An-jump blocks (2) Spacers (6) Felt Pads (2)
Track stops (2) T-guide screws (2) Lock washers (4) Hex lag bolts (6) An-jump block screws (4) Hex nuts (4) Rubber bumper bands (2)
Using the carriage
bolts, hex nuts and
lock washers, aach
the J-strap hangers to
the door as shown in
the diagram.
DOOR
TRACK
Door Edge
3”
1”
3 ½”
1 ⁄”
1 ⁄”
Stay:
Place 1 pad on top of track at
each end 1.
DOOR
TRACK
FINISHED OPENING
DOOR EDGE
½ʺ
ʺ
11
1
1ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
Using the T-guide screws, aach the T-guide to the floor
by aligning the edge of the guide with the edge of the
finished opening as shown above.
finished floor
WALL
DOOR
FINISHED FLOOR
Plumb the door before fastening door guide to floor.
Hanger Installation
T-guide Installation
Std Hardware Pack
installed with no casing,
base, or other trim.
Finished Opening
Header / Block
WALL
DOOR
Std Hardware Pack installed on track
trim board that is equal or thicker than
casing, base, or other trim.
Finished Opening
Header / Block
WALL
Head Track Block
Side Casing
Base Board
DOOR
Std Hardware Pack + ½”Extension Kit
installed where casing, base, or
other trim, is up to ½” thick .
Finished Opening
Header / Block
WALL
½ ʺ Extensions
DOOR
Side Casing
Base Board
Std Hardware Pack + 7/8” Extension Kit
installed where casing, base, or
other trim, is 5/8” to 1” thick .
Finished Opening
Extensions
Header / Block
WALL
DOOR
Side Casing
Base Board
⁄ ʺ
10488 W Cennt
enial Rd, Suite 100
Lileton, CO 80127
Goldberg Brothers, Inc.
[phone]
In the closed posion,
the door should
overlap the wall a
minimum of ⁄ʺ the top
and a minimum of ⁄ʺ
on both sides.
The edge of the door
should align with the
end of the track.
J-strap hanger.
Note: Aer the door is
hung from the track,
the an-jump blocks
can be installed
directly behind the
3ʺ from both sides of the top half of the door,
measure down 1⁄ʺ and 5⁄ʺ and drill ⁄ʺ pilot holes
followed by ⁄ʺ holes.
For large projects, installaon templates are
available for purchase.
5⁄ʺ
1⁄ʺ
3ʺ
Door Prep and Hanger Installaon
T-guide Installaon
Basic Installaon Layouts
Premium hardware set
installed with no casing,
base, or other trim.
FINISHED OPENING
HEADER/BLOCK
WALL
DOOR
Premium hardware set installed to
track trim board that is equal to, or thicker
than casing, base, or other trim.
FINISHED OPENING
HEADER/BLOCK
WALL
DOOR
Head Track Block
SIDE CASING
Base Board
Premium hardware set +
extension
kit installed where casing, base, or
other trim is greater than .
FINISHED OPENING
Extensions
Header / Block
WALL
DOOR
Side Casing
Base Board
FINISHED OPENING
HEADER/BLOCK
WALL
½ʺ Extensions
DOOR
Side Casing
Base Board
Premium hardware set + ½” extension
kit installed where casing, base, or
other trim is up to ½ʺ thick.
⁄ʺ or 1⁄ʺ
1
3
3
⁄ʺ or 1⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
Attach the
exposed roller
hangers and anti-
jump blocks to the
door as shown in
3” from both sides of the top half of the door,
measure down 1⁄” and 5” and drill ⁄” pilot holes
followed by ⁄” pilot holes
For large projects door templates are available
for purchase
4”
1-⁄”
2-⁄”
FINISHED OPENING
HEADER/BLOCK
WALL
DOOR
SIDE CASING
BASE BOARD
5⁄ʺ
2ʺ
An-jump
block
Stay felt
pad
Bumper felt pad
Stay:
At each end of the track,
place one felt pad strip on
top of the track, 1⁄ʺ in from
the track stop as shown.
An-jump block
For each hanger, place one felt pad
strip on the track stop or the edge
of the hanger as shown.
Place one of the provided rubber
bumper bands around each stop.
OR
Bumper:
1⁄ʺ
This warranty does not include loss or defects caused by elements outside the control of
Goldberg Brothers , such as natural disasters, weather, fire, water leakage, abuse, improper
installaon, or anything else deemed out of the control of Goldberg Brothers.
With the excepon of our stainless steel products, Goldberg Brothers does not warrant any
products installed and used outdoors or where they are exposed to weather, running water
or water condensaon. Under these condions, rust and other damage will naturally occur.
Goldberg Brothers does not warrant the loss of finish at points where roller is in contact with
track. Goldberg Brothers barn door hardware is sold as a rusc finished hardware and
Goldberg Brothers does not warrant the imperfecons seen through the finish in the steel
parts. It is part of the look.
Goldberg Brothers barn door track and hardware sets come with a one-year manufacturer’s
warranty for defecve parts under normal installaon and use. Warranty is subject to repair
or replacement of defecve components at manufacturer’s discreon and does not include
installaon costs.
GOLDBERG BROTHERS BARN DOOR HARDWARE
Premium Series J-strap hardware set - Installation Instructions
60013H-*, 60014H-*, 60015H-*, 60015UH-*