Manual

ManualsBrandsGolden Blount ManualsKilnSF 3624 TV

INSTALLATION AND OPERATING INSTRUCTIONS

GOLDEN BLOUNT

SUPER-FIRE

MODEL SF3624-TV TOP-VENT FIREPLACE

CSA APPROVED FOR NATURAL GAS OR PROPANE GAS

IMPORTANT! Read all instructions carefully before starting

installation. Failure to follow these instructions may result in

property damage, personal injury or possible loss of life.

WARNING: If the information in these

instructions is not followed exactly, a

ﬁre or explosion may result causing

property damage, personal injury or

death.

– Do not store or use gasoline or other

ﬂammable vapors and liquids in the

vicinity of this or any other appliance.

– WHAT TO DO IF YOU SMELL

GAS:





do not use any phone in your





from a neighbor’s phone. Follow the

gas supplier’s instructions.



supplier, call the ﬁre department.

– Installation and service must be

performed by a qualiﬁed installer,

service agency or the gas supplier.

■ The Flue Damper must be in the

full open position when burning the

gas logs.

■ This ﬁreplace is to be burned only

with the gas log set supplied with the

ﬁreplace. Burning other items could

cause a ﬁre hazard or injury.

■ For best results, Natural Gas pressure

should be 7" to 12" W.C. and 11" W.C.

for Propane Gas.

■ To simulate real wood burning, the gas

burner is designed to burn a yellow

ﬂame. It is normal for the logs to soot-

up. The soot can be easily removed

with a vacuum cleaner or soft brush.

■ Check the label on the ﬁrebox to

assure the proper gas type. Never

use anything but the correct gas type

for your ﬁreplace.

This appliance complies with National

Safety and is tested and listed to ANSI

Z21.50b - 2009 as Vented Gas ﬁreplaces.

Installation must conform to local codes.

In the absence of local codes, installation

must conform with the current National

Fuel Gas Code, ANSI Z223.1.

5/13

MANUFACTURED BY:

4301 WESTGROVE DRIVE

ADDISON TX. 75001

INSTALLER/CONSUMER RETAIN THIS APPLIANCE

MANUAL WITH THE INSTALLED APPLIANCE

Summary of content (25 pages)

PAGE 1
INSTALLER/CONSUMER RETAIN THIS APPLIANCE MANUAL WITH THE INSTALLED APPLIANCE INSTALLATION AND OPERATING INSTRUCTIONS GOLDEN BLOUNT SUPER-FIRE MODEL SF3624-TV TOP-VENT FIREPLACE CSA APPROVED FOR NATURAL GAS OR PROPANE GAS IMPORTANT! Read all instructions carefully before starting installation. Failure to follow these instructions may result in property damage, personal injury or possible loss of life.
PAGE 2
TABLE OF CONTENTS SECTION Layout Options ............................................................................................................... 2 Identification of Parts ...................................................................................................... 3 Building Codes and Safety Standards............................................................................. 4 Piping and Gas Pressure Requirements.........................................................................
PAGE 3
SF3624-TV TOP-vent fireplace Damper Control Lever Stand Offs Valve Access Panel Outside Air Port interior view Damper Control Lever Pan Burner Pilot Light Outside Air Control Knob On/Off Switch 3
PAGE 4
BUILDING CODES AND SAFETY STANDARDS The design of this FIREPLACE ACCESSORY has been tested and is listed with CSA INTERNATIONAL in accordance with THE AMERICAN NATIONAL STANDARDS INSTITUTE - ANSI Z21.50, CSA Test Report No. 188842-1049553. This manual serves only as a basic guideline for installation and use of this firebox and gas piping.
PAGE 5
GAS PIPING AND GAS PRESSURE REQUIREMENTS All gas piping must be installed to comply with local codes, or, in the absence of local codes, with the latest edition of the National Fuel Gas Code ANSI Z223.1. Unions in gas lines shall be of ground joint type. Compounds used on threaded joints of gas piping must be resistant to the action of liquefied petroleum gas. Gas piping must be of sufficient size to provide a minimum natural gas pressure at the appliance of 7" water column or 11" for L.P.
PAGE 6
INSTALLATION INSTRUCTIONS In planning the installation for the fireplace it is necessary to determine where the unit is to be installed, the routing of the B-type vent system, and whether optional accessories are to be used gas supply piping should also be planned. Model SF3624-TV (with the use of the Outside Air Kit) can be installed in a bedroom (in the United States) which has a total volume of unconfined space appropriate to the particular installation. Refer to the National Fuel Gas Code ANSI Z223.
PAGE 7
31" TOP VIEW UNIT DIMENSIONS FOR CONSTRUCTION PLANNING 10 1/2" 23 1/2" FRONT VIEW SIDE VIEW 42" 6" 41 3/16" MINIMUM FRAMING DIMENSIONS 46" OPENING HEIGHT 24" 14" 2.5" 7" 36" Figure 7.1 SIDE DOOR MODEL 24" 45" Installing Chimney/Vent System FRONT OF APPLIANCE 6.5" REFRACTORY MODEL HOLE FOR GAS LINE Model SF3624TV is approved to be used with 8" B-Type Gas Vent or 8" class-A All Fuel Chimney.
PAGE 8
Installing Outside Air Kit Model SF3624-TV is supplied with the component parts for outside combustion with the exception of the 4" flex duct. It is recommended that the outside air system be used whenever possible. Connect 4" Class-1 Flex duct or Metal Vent to duct collar on side of firebox, run duct to fresh air source and terminate using duct termination cap. The Outside air can be opened by pushing control knob toward back of fireplace and closed by pulling towards front (Refer to figure 7.2).
PAGE 9
INSTALLATION INSTRUCTIONS REFRACTORY BRICK PANELS, DOWNDRAFT DIVERTER, AND EXHAUST DIVERTER SF3624 SUPERFIRE FIREPLACE This model Golden Blount top vent fireplace is supplied with high quality realistic Refractory Brick Panels. These panels are massive and must be field-installed to prevent damage to panels or fireplace during shipping. The field installation of panels also requires the Downdraft Diverter, and Exhaust Diverter to be installed in the field as well.
PAGE 10
EXHAUST DIVERTER INSTALLATION The Exhaust Diverter prevents exhaust gasses from entering the room. 1. Locate screws attached to front side top of interior firebox and remove. (Figure 3). 2. Position Exhaust Diverter into fireplace and attach Diverter using screws removed earlier. Diverter should be positioned as shown. (Figure 4).
PAGE 11
LOG PLACEMENT FOR MODEL# SF3624TBF LOG SET NOTE: FOR SF3624 STACK LOG PLACEMENT, SEE SHEET IN LOG CTN. 3 2 7 6 1 4 5 Placement Instructions • Place the back bottom log (log #1) as shown in the Illustration above. It should be positioned on the back of the grate. • Place the front bottom log pieces (logs #2 and #3) as shown. They should be positioned on the front of the grate.
PAGE 12
OPTIONAL GLASS DOOR INSTALLATION 1. INSTALL GB DOOR TRACKS AND HINGE SPRINGS AS ILLUSTRATED IN FIGURE 1 USING 6 SCREWS IN KIT. 2. SCREW HANDLES ON TO DOORS. door track (top) 3. INSTALL DOORS AS SHOWN IN FIGURE 2. NOTE! hinge spring BRIDGE ❒ HINGE SPRINGS CAN BE MOVED TO ADJUST DOOR ALIGNMENT. ❒ DOOR LOCKING TABS CAN BE SET BY BENDING UP OR DOWN. SEE FIGURE 3. ❒ USE MILD SOAP AND WATER TO CLEAN METAL SURFACES. DOOR TRACK (BOTTOM) Figure #1 ❒ DO NOT USE BRASS OR ABRASIVE CLEANERS.
PAGE 13
OPERATING GUIDELINES (CONT’D) When lit for the first time, the appliance will emit a slight odor for an hour or two. This is due to paint and lubricants used in the manufacturing process. The main burner flame characteristics are steady, not lifting or floating. Typically, the top 3/4 inch of the pilot generator should be engulfed in the pilot flame. A periodic check of these characteristics is necessary.
PAGE 14
FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. C. Use only your hand to push in or turn the gas A. This appliance has a pilot. When lighting control knob. Never use tools. If the knob will not the pilot, follow these instructions exactly. push in or turn by hand don’t try to repair it, call a qualified service technician. Forced or attempted B.
PAGE 15
TO TO TURN TURN OFF OFF GAS GAS TO TO APPLIANCE APPLIANCE 1. Open valve access door panel ➤ to pilot position then depress and continue turning to “OFF” 2. Turn knob clockwise 3. Close access door panel LPG (PROPANE) WARNING THE FOLLOWING WARNING APPLIES TO INSTALLATIONS USING L.P. (PROPANE GAS): WARNING: To avoid possible injury, fire and explosion, please read and follow these precautions and all instructions of this appliance before lighting the pilot. This appliance uses L.P.
PAGE 16
TROUBLE SHOOTING (Millivolt MODEL) With proper installation and maintenance, your new Gas Fireplace should provide years of trouble-free service. If you do experience a problem, refer to the trouble shooting guide shown below. This guide will assist a qualified service person in the diagnosis of problems and the corrective action to be taken. SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Spark ignitor will not light A. Defective ignitor (no 1. Check for spark at pilot after triggering spark at electrode).
PAGE 17
TROUBLE SHOOTING (CONT’D) SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 2. Pilot will not stay lit A. Defective pilot 1. Check pilot, flame must after carefully following generator impinge on pilot generator. lighting instructions. Clean and or adjust pilot for maximum flame impingement on generator. 2. Be sure wire connections from generator at gas valve terminals are tight and generator is fully inserted into pilot bracket. 3.
PAGE 18
TROUBLE SHOOTING (CONT’D) SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 3. Pilot burning, no A. Damper control lever in 1. Set damper control lever gas burner, valve knob closed position to open position. “ON”, “ON/OFF” switch “ON”. B. “ON/OFF” switch or 1. Check ON/OFF switch wires defective and wires for proper connections. Place jumper wires across terminals at switch-if burner comes on, replace defective switch.
PAGE 19
TURN OFF GAS TO APPLIANCE OPERATINGTO GUIDELINES (STP-SPARK TO PILOT MODEL) Upon completing the gas line connection, a small amount of air will be in the lines. When first lighting the pilot light, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the pilot and burner will light and operate as indicated in the instruction manual. Subsequent lighting of the appliance will not require such purging.
PAGE 20
Flame Sensor WIRING DIAGRAM (STP-SPARK TO PILOT MODEL) remote/wall switch connection FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. This appliance is equipped with an ignition device which automatically lights the pilot. Do not light pilot by hand. B. BEFORE LIGHTING smell all around the appliance area for gas.
PAGE 21
LIGHTING INSTRUCTIONS Elec. spark to pilot 1. “STOP” Read the safety information on page 11. 2. Set the switch to “OFF”. 3. Remove batteries from battery pack. 4. This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand. 5. Wait (5) minutes to clear out any gas. Then smell for gas, including near rgw floor. If you smell gas, STOP! Follow “B” in the safety information on page 13. If you don’t smell gas, go to next step. 6.
PAGE 22
LPG (PROPANE) WARNING (CONT’D) IMPORTANT: Always keep the appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. Never obstruct the flow of combustion and ventilation air. Keep the front of the appliance clear of all obstacles and materials. To obtain proper operation, it is imperative that the pilot and main burner flame characteristics are steady, not lifting or floating.
PAGE 23
TROUBLE SHOOTING (CONT’D) SYMPTOM Pilot will not stay lit POSSIBLE CAUSE CORRECTIVE ACTION 1. Loose wiring on ignitor wire to ignition module and/or poor ground to ignition module 1. Check wiring connection. Refer to wiring diagram (see Wiring Diagram, page 20) 2. Pilot flame too low to sense 3. Flame sensor defective 2. Clean and adjust pilot burner and check gas supply and inlet pressure to unit Note: Have a qualified technician replace pilot assembly if broken or corroded 3.
PAGE 24
REPLACEMENT PARTS ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART # TV-101 TV-102 TV-103 TV-104 TV-105 TV-106 TV-107 TV-108 TV-109 TV-110 TV-111 TV-112 TV-113 TV-114 TV-115 TV-116 DESCRIPTION ITEM Gas Valve - N/G 17 Gas Valve - LP 18 “1/4" Pilot Line” 19 “3/8" Burner Line” 20 Piezo Ignitor 21 On/Off Switch 22 Pilot Assembly - Nat.
PAGE 25
TWO YEAR LIMITED WARRANTY This warranty is limited to top-vent gas fireplaces manufactured and assembled by Golden Blount. If Golden Blount finds that any part or portion of the fireplace covered by this warranty is defective in material or workmanship under normal use and service as described in the installation and operating instructions, Golden Blount will take the following actions: 1.