Installation Sheet

Assembly Instructions: 0804-4P (Abingdon)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above.
Shut off the power at the circuit breaker and completely remove the old xture
from the ceiling, including the old mounting strap.
1. From the parts bag remove the mounting strap assembly. One end of nipple (F)
should be attached to mounting strap (A) with washer (C) and hex nut (D) in place.
The other end should have canopy loop (H) attached. Attach mounting strap (A) to
the junction box using mounting screws (B) and a screwdriver. Tighten securely.
2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the
mounted canopy loop to test the height. Approximately half of the canopy loop’s
exteriorthreadsshouldbeexposed,andthecanopyloopcollarshouldtsnugly
onto the canopy loop. Remove canopy (G) and adjust the height of nipple (F) and
canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE
Note: Be careful when handling glass panels (R). GLASS EDGES ARE SHARP!
3.Placeframe(S)onaatsurface.Carefullytakeglasspanels(R)outofthebox.
Matcheachpanelwiththecorrectsideofthexture.Carefullyplaceglasspanels
(R) inside of frame (S) and secure each in place by carefully bending tabs (Q) onto
glass panels (R).
4. Away from the assembled frame (S), placethelampbodyonitssideonaat
surface.Placetopcap(M)closetothelampbody.Passthexture’swiresthrough
theholeatthecenteroftopcap(M).Threadrod(N)intotopcap(M).Locktherodin
place by threading top loop (L) onto the threads of rod (N) exposed above top cap
(M). Pull the wires taut through top loop (L).
5. Have an assistant help you. Carefully place top cap (M) on top of frame (S) so
that the lamp body is inside of frame (S). Screw deco nuts (O) onto the ends of deco
screws (P) to connect top cap (M) to frame (S).
6. By measuring, determine the correct numberof chainlinks neededfor proper
hanging height. If necessary, use a pair of pliers to open and remove any excess
chain.
7. Attach chain connectors (K) to each end of chain (J) before attaching one end of
the chain connector/chain to top loop (L). Close the chain connector. Connect the
otherchainconnector (K) to canopy loop (H). Pass the xture’s wiresupthrough
chain(J)(everythreelinksorso).Slidecanopyloopcollar(I)andcanopy(G)onto
the chain/wire.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
8.Haveanassistantsupporttheweightofthexturewhilecompletingthewiring.Cutawayexcesswire.Threadthexture’swiresthrough
canopyloop(H)andnipple(F).Attachthexture’swirestothepowersupplywiresfromthejunctionbox.Connectblacktoblack(orsmooth);
whitetowhite(orribbed);groundtoground(greenorcopper).Twisttheendsofthewirepairstogether,andthentwistonawireconnector.
Makesurealltwistsareinthesamedirection.Ifthereisnogroundwire(greenorcopper)comingfromthejunctionbox,locategroundscrew
(E)onmountingstrap(A)andwrapthexture’sgroundwirearoundthegreengroundscrew(E).Useascrewdrivertosecuregroundscrew(E)
ontothemountingbracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
10. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy
loop (H) to secure canopy (G) in place.
11. Use thelatch on theside of frame(S) to open the door on the side of the xture. Reach in and install light bulbs (not provided) in
accordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
A
C
B
D
E
F
H
I
G
J
K
L
M
N
O
P
Q
R
T
S
HANDLE WITH CARE!
GLASS EDGES ARE SHARP!
GLASS EDGES
ARE SHARP!