Installation Sheet

Assembly Instructions: 0806-S (Keating)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off
thepoweratthecircuitbreakerandcompletelyremovetheoldxturefromtheceiling,
including the old mounting strap.
1. From the parts bag remove the mounting strap assembly. One end of nipple (F)
shouldbeattachedtomountingstrap(A)withwasher(C)andhexnut(D)inplace.
The other end should have canopy loop (H) attached. Attach mounting strap (A) to the
junctionboxusingmountingscrews(B)andascrewdriver.Tightensecurely.
2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the
mounted canopy loop to test the height. Approximately half of the canopy loop’s
exteriorthreadsshouldbeexposed,andthecanopyloopcollarshouldtsnuglyonto
the canopy loop. Remove canopy (G) and adjust the height of nipple (F) and canopy
loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE
3. Thread nipple (N) into post (O). Thread top cap (M) followed by top loop (L) onto the
exposedthreadsofnipple(N).Pullthewiresthroughtoploop(L)untiltaut.
4. By measuring, determine the correct number of chain links needed for proper
hangingheight.Ifnecessary,useapairofplierstoopenandremoveanyexcesschain.
5. Attach chain connectors (K) to each end of chain (J) before attaching one end of
the chain connector/chain to the top loop (L). Close the chain connector. Connect the
other chain connector (K) to canopy loop (H).
6.Passthexture’swiresupthroughchain(J)(everythreelinksorso).Slidecanopy
loop collar (I) and canopy (G) onto the chain/wire.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
7.Haveanassistantsupporttheweightofthexturewhilecompletingthewiring.Cut
awayexcesswire.Threadthexture’swiresthroughcanopyloop(H)andnipple(F).
Attachthexture’swirestothepowersupplywiresfromthejunctionbox.Connectblack
to black (or smooth); white to white (or ribbed); ground to ground (green or copper).
Twisttheendsofthewirepairstogether,andthentwistonawireconnector.Makesure
all twists are in the same direction. If there is no ground wire (green or copper) coming
fromthe junction box, locate groundscrew(E) on mounting strap (A) and wrap the
xture’sgroundwirearoundthegreengroundscrew(E).Useascrewdrivertosecure
groundscrew(E)ontothemountingbracket.Tuckallwiresneatlyintothejunctionbox.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
A
C
B
D
E
F
H
I
G
J
K
L
M
N
O
P
FINISHING THE INSTALLATION
8. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy
loop (H) to secure canopy (G) in place.
9.
Installalightbulb(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.

Summary of content (1 pages)