Installation Sheet

Assembly Instructions: 0839-4P (Haiden)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut
offthepoweratthecircuitbreakerandcompletelyremovetheoldxturefromthe
ceiling, including the old mounting strap.
1. From the parts bag remove the mounting strap assembly. One end of nipple
(F)shouldbeattachedtomountingstrap(A)withwasher(C)andhexnut(D)in
place. The other end should have canopy loop (H) attached. Attach mounting
strap(A)tothejunctionboxusingmountingscrews(B)andascrewdriver.Tighten
securely.
2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the
mountedcanopylooptotesttheheight.Approximatelyhalfofthecanopyloop’s
exteriorthreadsshouldbeexposed,andthecanopyloopcollarshouldtsnugly
onto the canopy loop. Remove canopy (G) and adjust the height of nipple (F) and
canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE
3. Thread nipple (N) into post (O). Thread top cap (M) followed by top loop (L) onto
theexposedthreadsofnipple(N).Pullthewiresthroughtoploop(L)untiltaut.
4. By measuring, determine the correct number of chain links needed for proper
hangingheight.Ifnecessary,useapairofplierstoopenandremoveanyexcess
chain.
5. Attach chain connectors (K) to each end of chain (J) before attaching one
end of the chain connector/chain to the top loop (L). Close the chain connector.
Connect the other chain connector (K) to canopy loop (H).
6. Pass the xture’s wires up through chain (J) (every three links or so). Slide
canopy loop collar (I) and canopy (G) onto the chain/wire.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
7.Haveanassistantsupporttheweightofthexturewhilecompletingthewiring.
Cutawayexcesswire.Threadthexture’s wiresthroughcanopyloop(H)and
nipple(F).Attachthexture’swirestothepowersupplywiresfromthejunction
box.Connectblackto black (orsmooth);whitetowhite (orribbed);groundto
ground (green or copper). Twist the ends of the wire pairs together, and then
twist on a wire connector. Make sure all twists are in the same direction. If there
isnogroundwire(greenorcopper)comingfromthejunctionbox,locateground
screw(E) onmountingstrap(A) andwrapthexture’s groundwirearoundthe
green ground screw (E). Use a screwdriver to secure ground screw (E) onto the
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
8. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy
loop (H) to secure canopy (G) in place.
9. Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
A
C
B
D
E
F
H
I
G
J
K
L
M
N
O
P
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread