Installation Sheet

Assembly Instructions: 0885-4P (Laurent)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely remove
theoldxturefromtheceiling,includingtheoldmountingstrap.
1.Fromthepartsbagremovethemountingstrapassembly.Oneend
ofnipple(F)shouldbeattachedtomountingstrap(A)withwasher(C)
andhexnut(D)inplace.Theotherendshouldhavecanopyloop(H)
attached.Attachmountingstrap(A)tothejunctionboxusingmounting
screws(B)andascrewdriver.Tightensecurely.
2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy
(G)overthemountedcanopylooptotesttheheight.Approximately
halfofthecanopyloop’sexteriorthreadsshouldbeexposed,andthe
canopy loop collar should t snugly onto the canopy loop. Remove
canopy(G)andadjusttheheightofnipple(F)andcanopyloop(H)until
thedesiredheightisreached.
ASSEMBLING THE FIXTURE
3. Thread rod (N) into post (O) at the center of the lamp cluster. Top
loop(L)is connected totopcap(M). Pull thewirestaut throughtop
loop (L) and thread the bottom of top loop (L) into the top of rod (N).
Use thumb screws (Q) toconnect top cap (M) to the xture’s cage/
body (P).
4.Bymeasuring,determinethecorrectnumberofchainlinksneeded
forproperhangingheight.Ifnecessary,useapairofplierstoopenand
removeanyexcesschain.
5.Attachchainconnectors(K)toeachendofchain(J)beforeattaching
oneendofthechainconnector/chaintotoploop(L).Closethechain
connector. Connect the other chain connector (K) to canopy loop (H).
6.Passthexture’swiresupthroughchain(J)(everythreelinksorso).
Slidecanopyloopcollar(I)andcanopy(G)ontothechain/wire.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
7.Haveanassistantsupporttheweightofthexturewhilecompleting
the wiring. Cut away excess wire. Thread the xture’s wires through
canopyloop(H)andnipple(F).Attachthexture’swirestothepower
supplywiresfromthejunctionbox.Connectblacktoblack(orsmooth);
whitetowhite(orribbed);groundtoground(greenorcopper).Twistthe
endsofthewirepairstogether,andthentwistonawireconnector.Make
surealltwistsareinthesamedirection.Ifthereisnogroundwire(green
orcopper) coming fromthejunctionbox,locateground screw(E)on
mountingstrap(A)andwrapthexture’sgroundwirearoundthegreen
groundscrew(E).Useascrewdrivertosecuregroundscrew(E)ontothe
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
8.Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)ontocanopy
loop (H) to secure canopy (G) in place.
9. Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
A
C
B
D
E
F
H
I
G
J
K
L
N
M
R
Q
P
O