Installation Sheet

Assembly Instructions: 1157-3P (Payton)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. Dry with a lint-free or microber cloth.
For Customer Service, contact
the place of purchase
Smooth / Black /
Transparent (L)
Black (Hot)
Ribbed / White /
Transparent (N)
Bare Copper / Transparent with
Green Interior / Green
White (Neutral)
Green
(Ground)
PREPARING FOR INSTALLATION
Please Note: The cage, light source, and glass shade are pre-assembled.
Remove all of the contents from the carton. See the important notes above.
Shutoffthepoweratthecircuitbreakerandcompletelyremovetheoldxture
from the ceiling, including the old mounting strap.
From the parts bag remove the mounting strap assembly. One end of nipple
(F)shouldbeattachedtomountingstrap(A)withhexnuts(C,D)inplace.The
other end should have canopy loop (H) attached.
Match the threaded holes of mounting strap (A) to the spacing of the holes on
thejunctionbox.Attachmountingstrap(A)tothejunctionboxusingmounting
screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop collar (I)
from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test
theheight.Approximatelyhalfofthecanopyloop’sexteriorthreadsshouldbe
exposed,andthecanopyloopcollarshouldtsnuglyontothecanopyloop.
Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H)
until the desired height is reached.
ASSEMBLING THE FIXTURE
Screw top loop (L) onto the threads of post (M). By measuring, determine the
correct number of chain links needed for proper hanging height. If necessary,
useapairofplierstoopenandremoveanyexcesschain.Attachonechain
connector (K) to each end of chain (J). Use one of chain connectors (K)
to attach chain (J) to top loop (L) and close the chain connector. Feed the
xture’swiresupthroughthechain(everythreelinksorso),pullingthewires
until taut. Slide canopy loop collar (H) and canopy (G) onto the chain and
wires. Use the free chain connector (K) to attach chain (J) to canopy loop (H).
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cut
awayexcesswire.Threadthexture’swiresthroughcanopyloopandnipple.
Attachthexture’swirestothepowersupplywiresfromthejunctionbox.
Connect black to smooth/black/transparent (L) wire; white to ribbed/white/
transparent (N) wire; ground to ground (green or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no ground wire (green or copper) from
thejunctionbox,locategroundscrew(E)onmountingstrap(A)andwrapthe
xturegroundwirearoundthegreengroundscrew(E).Useascrewdriverto
secure ground screw (E) onto the mounting bracket/mounting strap. Tuck all
wiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath
the canopy. Tightly thread canopy loop collar (I) onto canopy loop (H) to
secure canopy (G) in place.
Install bulbs (Q) (not included) in candles sleeves (P) in accordance with the
xture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
Q
N
L
M
I
H
B
F
K
J
G
D
C
K
P
O
E
A