Installation Sheet

Assembly Instructions: 1323-6 (Ella)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off
thepoweratthecircuitbreakerandcompletelyremovetheoldxturefromtheceiling,
includingtheoldmountingstrap.
Fromthepartsbag,removethemountingstrapassembly.Oneendofnipple(F)should
beattachedtomountingstrap(A)withhexnuts(C,D)inplace.Theotherendshould
have canopy loop (H) attached.
Attachmountingstrap(A)tothejunctionboxusingmountingscrews(B)anda
screwdriver.Tightensecurely.Unscrewcanopyloopcollar(I)fromcanopyloop(H).Pass
crystalplate(W),metaldisc(V)andcanopy(G)overthemountedcanopylooptotestthe
height.Approximatelyhalfofthecanopyloop’sexteriorthreadsshouldbeexposed,and
thecanopyloopcollarshouldtsnuglyontothecanopyloop.Removecrystalplate(W),
metaldisc(V)andcanopy(G).Adjusttheheightofnipple(F)andcanopyloop(H)untilthe
desiredheightisreached.
ASSEMBLING THE FIXTURE
Rotatethearmsofthextureuntiltheyareinposition.Usedecorativenuts(P)toattach
arms(O)toposts(N)ofthexture’sbody.
Bymeasuring,determinethecorrectnumberofchainlinksneededforproperhanging
height.Ifnecessary,useapairofplierstoopenandremoveanyexcesschain.Attach
one chain connector (K) to each end of chain (J). Use one of chain connectors (K) to
attachchain(J)totoploop(L)andclosethechainconnector.Feedthexture’swiresup
throughthechain(everythreelinksorso),pullingthewiresuntiltaut.Slidecanopyloop
collar (H) and canopy (G) onto the chain/wire. Use the free chain connector (K) to attach
chain (J) to canopy loop (H).
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cutaway
excesswire.Threadthexture’swiresthroughcanopyloopandnipple.Attachthe
xture’swirestothepowersupplywiresfromthejunctionbox.Connectblacktosmooth/
black/transparent(L)wire;whitetoribbed/white/transparent(N)wire;groundtoground
(greenorcopper).Twisttheendsofthewirepairstogether,andthentwistonawire
connector.Makesurealltwistsareinthesamedirection.Ifthereisnogroundwire(green
orcopper)fromthejunctionbox,locategroundscrew(E)onthemountingbracket/
mountingstrapandwrapthexture’sgroundwirearoundthegreengroundscrew(E).
Useascrewdrivertosecuregroundscrew(E)ontothemountingbracket/mountingstrap.
Tuckallwiresneatlyintothejunctionbox.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. Dry with a lint-free or microber cloth.
For Customer Service, contact
the place of purchase.
FINISHING THE INSTALLATION
Pushcrystalplate(W),metaldisc(V)andcanopy(G)uptotheceiling.Slidecanopyloopcollar(I)upbeneaththecrystalplate(W).
Tightlythreadcanopyloopcollar(I)ontocanopyloop(H)tosecurecanopy(G)inplace.Slidecandlesleeves(R)ontosockets(S).
Installbulbs(Q)(notincluded)inaccordancewiththexture’sspecications.Donotexceedthemaximumwattage.Refertothe
crystalinstallationsheettohangthecrystals.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
Smooth / Black /
Transparent (L)
Black (Hot)
Ribbed / White /
Transparent (N)
Bare Copper / Transparent with
Green Interior / Green
White (Neutral)
Green
(Ground)
A
B
C
G
H
I
L
J
K
F
E
D
N
O
P
Q
R
S
T
U
M
V
W