Installation Sheet

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
PREPARING FOR INSTALLATION
PleaseNote:Thecage,andxturebody(R)arepre-assembled.Removeallofthecontents
fromthecarton.Seetheimportantnotesabove.Shutoffthepoweratthecircuitbreakerand
completelyremovetheoldxturefromtheceiling,includingtheoldmountingstrap.Fromthe
partsbagremovethemountingstrapassembly.Oneendofnipple(F)shouldbeattachedto
mountingstrap(A)withhexnuts(C,D)inplace.Theotherendshouldhavecanopyloop(H)
attached.
Matchthethreadedholesofmountingstrap(A)tothespacingoftheholesonthejunctionbox.
Attachmountingstrap(A)tothejunctionboxusingmountingscrews(B)andascrewdriver.
Tightensecurely.Unscrewcanopyloopcollar(I)fromcanopyloop(H).Passcanopy(G)overthe
mountedcanopylooptotesttheheight.Approximatelyhalfofthecanopyloop’sexteriorthreads
shouldbeexposed,andthecanopyloopcollarshouldtsnuglyontothecanopyloop.Remove
canopy(G)andadjusttheheightofnipple(F)andcanopyloop(H)untilthedesiredheightis
reached.
ASSEMBLING THE FIXTURE
Placexturebody(R)ontoaatsurface.Rod(N)isonthexture’swires,butnotattachedtothe
bodyofthexture.Passthexture’swiresthroughrod(N)andpullthewiresuntiltaut.Twistrod
(N)ontothepostatthecenterofthexturebody(R)untilsecure.Bymeasuring,determinethe
correctnumberofchainlinksneededforproperhangingheight.Ifnecessary,useapairofpliers
toopenandremoveanyexcesschain.Attachonechainconnector(K)toeachendofchain(J).
Useoneofchainconnectors(K)toattachchain(J)totoploop(L)andclosethechainconnector.
Hooktheendofrod(N)ontotoploop(L).Pullthewiresthroughtoploop(L).Feedthexture’s
wiresupthroughthechain(everythreelinksorso),pullingthewiresuntiltaut.Slidecanopyloop
collar(H)andcanopy(G)ontothechain/wires.Usethefreechainconnector(K)toattachchain
(J)tocanopyloop(H).
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cutawayexcess
wire.Threadthexture’swiresthroughcanopyloopandnipple.Attachthexture’swirestothe
powersupplywiresfromthejunctionbox.Connectblacktosmooth/black/transparent(L)wire;
whitetoribbed/white/transparent(N)wire;andgroundtoground(greenorcopper).Twistthe
endsofthewirepairstogether,andthentwistonawireconnector.Makesurealltwistsareinthe
samedirection.Ifthereisnogroundwire(greenorcopper)fromthejunctionbox,locateground
screw(E)onmountingstrap(A)andwrapthexture’sgroundwirearoundthegreenground
screw(E).Useascrewdrivertosecuregroundscrew(E)ontothemountingbracket/mounting
strap.Tuckallwiresneatlyintothejunctionbox.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microber cloth.
AssemblyInstructions:2073-3P, 2074-3P(Smyth)
A
B
C
H
I
G
J
K
E
D
F
L
M
P
R
O
N
S
Q
For Customer Service, contact the
place of purchase.
FINISHING THE INSTALLATION
Raisecanopy(G)totheceilingandslidecanopyloopcollar(I)upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)ontocanopy
loop(H)tosecurecanopy(G)inplace.
Attachthehooksofrods(M)totoploop(L).Liftcage(P)upsothatrods(M)andxturebody(R)isinside.Holdcage(P)upandhavean
assistantattachthebottomloopsofrods(M)tothehooksinsidecage(P).Donotletgoofthecageuntilallrodsareattachedtocage
(P).Slidecandlesleeves(Q)overthesockets.Installlightbulbs(O)(notincluded)inaccordancewiththexture’sspecications.Carefully
slideglassshades(S)overcandlesleeves(Q)andsecuretheglassinplacebypushingtheglassdownontothesockettters.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
Smooth / Black /
Transparent (L)
Black (Hot)
Ribbed / White /
Transparent (N)
Bare Copper / Transparent with
Green Interior / Green
White (Neutral)
Green
(Ground)