Installation Guide

Assembly Instructions: 2073-SF12 (Smyth)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microber cloth.
For Customer Service, please
contact the place of purchase.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Remove the old
xture from the ceiling, including the old mounting strap.
1. Take the mounting strap assembly from the parts bag. Mounting strap (B) contains threaded
holes. Two of mounting screws (A) should be attached to mounting strap (B). You may need to
tighten nuts (C) that hold these screws in place.
2. Place mounting strap (B) over the junction box so that mounting screws (A) are vertical, and
inalignmentwiththeholelocationsonthexture’scanopy(G).Securemountingstrap(B)tothe
junction box with mounting screws (D) and a screwdriver. Tighten the screws securely.
3.Placethexture’ssocketcluster(R)onaatsurface.Rod(P)isonxture’swires(L),butnot
attachedtothebodyofthexture.Twistrod(P)ontothecenterpostonsocketcluster(R)until
secure and pull the wires until taut.
4.Slidemetalharp(M)downontoxture’swires(L)andoverthethreadsofrod(P).Pullthe
wires through swivel (J) and canopy (G) until taut. Tightly thread rod (P) with metal harp (M) still
on the threads onto post (K).
CONNECTING THE WIRES
5.Haveanassistantsupportthexture’s
weight while completing the wiring. Refer to the
wiringdiagrambelowandattachthexture’s
wires to the power supply wires from the
junction box. Connect Hot to Hot, Neutral to
Neutral, and Ground to Ground. Twist the ends
of the wire pairs together, and then twist on a
wire connector. Make sure all twists are in the
same direction. If there is no house ground wire
coming from the junction box, locate ground
screw (E) on the mounting bracket/mounting
strapandwrapthexture’sgroundwirearound
the ground screw. Use a screwdriver to tighten
the top of ground screw (E) onto the wires and
into the mounting bracket/mounting strap. Tuck
the wires into the junction box.
FINISHING THE INSTALLATION
6. Raise canopy (G) to the ceiling. Position mounting screws (A) so that they protrude through
the openings of canopy (G). Secure canopy (G) in place with decorative nuts (H).
7.Installlightbulbs(notincluded)inaccordancewiththexture’sspecications.
8. Raise glass shade (O) over the bottom of socket cluster (R). Line up the holes in glass shade
(O) with the holes in metal harp (M). Thread screws (N) with the included plastic washers into
the holes to connect glass shade (O) to metal harp (N).
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
G
N
D
D
C
E
A
B
G
H
I
J
K
L
M
N
O
R
P