Installation Sheet

Assembly Instructions: 3074-3P, 4P, 6P (Athena)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase.
Smooth / Black /
Transparent (L)
Black (Hot)
Ribbed / White /
Transparent (N)
Bare Copper / Transparent with
Green Interior / Green
White (Neutral)
Green
(Ground)
PREPARING FOR INSTALLATION
Please Note: The cage with light source is pre-assembled. Remove all of the contents
from the carton. See the important notes above. Shut off the power at the circuit
breakerandcompletelyremovetheoldxturefromtheceiling,includingtheold
mounting strap.
From the parts bag remove the mounting strap assembly. One end of nipple (G) should
beattachedtomountingstrap(A)withwasherandhexnut(CandF)inplace.Theother
end should have canopy loop (H) attached.
Match the threaded holes of mounting strap (A) to the spacing of the holes on the
junctionbox.Attachmountingstrap(A)tothejunctionboxusingmountingscrews(B)
and a screwdriver. Tighten securely. Unscrew canopy loop collar (I) from canopy loop
(H).Passcanopy(D)overthemountedcanopylooptotesttheheight.Approximately
halfofthecanopyloop’sexteriorthreadsshouldbeexposed,andcanopyloopcollar
(I)shouldtsnuglyontothecanopyloop.Removecanopy(D)andadjusttheheightof
nipple (G) and canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE
Screwtoploop(M)ontothethreadsofthexture’sbody.Bymeasuring,determinethe
correctnumberofchainlinksneededforproperhangingheight.Ifnecessary,useapair
ofplierstoopenandremoveanyexcesschain.Attachoneofchainconnector(K)to
each end of chain (J). Use one of chain connectors (K) to attach chain (J) to top loop (M)
andclosethechainconnector.Feedthexture’swiresupthroughthechain(everythree
linksorso),pullingthewiresuntiltaut.Slidecanopyloopcollar(I)andcanopy(D)onto
the chain and wires. Use the free chain connector (K) to attach chain (J) to canopy loop
(H).
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cutaway
excesswires.Threadthexture’swiresthroughcanopyloopandnipple.Attachthe
xture’swirestothepowersupplywiresfromthejunctionbox.Connectblackto
smooth/black/transparent (L) wire; white to ribbed/white/transparent (N) wire; ground to
ground(greenorcopper).Twisttheendsofthewirepairstogether,andthentwistona
wire connector. Make sure all twists are in the same direction. If there is no ground wire
(greenorcopper)fromthejunctionbox,locategroundscrew(E)onmountingstrap(A)
andwrapthexturegroundwirearoundthegreengroundscrew(E).Useascrewdriver
to secure ground screw (E) onto the mounting strap. Tuck all wires neatly into the
junctionbox.
FINISHING THE INSTALLATION
Push canopy (D) up to the ceiling and slide canopy loop collar (I) up beneath the
canopy. Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy (D)
in place.
Slide candle sleeves (Q) over sockets (P). Install the bulbs (R - not included) into sockets
(P)inaccordancewiththexture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
A
B
C
D
E
F
G
H
I
J
K
M
O
P
Q
R