Installation Sheet

Assembly Instructions: 3602-1W (Duncan)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microber cloth.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
C
B
E
D
A
F
G
H
I
J
K
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit
breaker and completely remove the old xture from the wall,
including the old mounting strap.
1. Mounting strap (B) contains several pairs of threaded holes.
Find the pair of holes that matches the spacing of the holes on
thejunctionboxandyourxturebackplate.Twoofmounting
screws(A)shouldbeattachedtomountingstrap(B).Youmay
needtotightenthenutsthatholdthesescrewsinplace.Pull
thehousewiresthroughthecenterofmountingstrap(B).Place
mounting strap (B) over the junction box so that mounting
screws(A)arehorizontal,andinalignmentwiththehole
locationsonthexturebackplate(F).Securemountingstrap(B)
tothejunctionboxwithmountingscrews(D)andascrewdriver.
Tightenthescrewssecurely.
CONNECTING THE WIRES
2.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothewiringdiagramandattachthexture’s
wirestothepowersupplywiresfromthejunctionbox.ConnectHottoHot(transparentwirewithblackinnerthread,black,or
smoothwire)NeutraltoNeutral(transparentwirewithwhiteinnerthread,white,orribbedwire),andGroundtoGround(transparent
wirewithgreeninnerthread,greenwire,orcopper).Twisttheendsofthewirepairstogether,andthentwistonawireconnector.
Makesurealltwistsareinthesamedirection.Ifthereisnohousegroundwirecomingfromthejunctionbox,locategroundscrew(E)
onthemountingbracket/mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.Useascrewdrivertotighten
thetopofgroundscrew(E)ontothewiresandintothemountingbracket/mountingstrap.Tuckthewiresintothejunctionbox.
FINISHING THE INSTALLATION
3.Placexturebackplate(F)overmountingscrews(A)sothattheyprotrudethroughtheholesinthefrontofthebackplate.Thread
deconuts(G)ontomountingscrews(A).Twistuntilbackplate(F)ofthextureissnugagainstthewall.
4.Slideshade(I)ontosocket(H)andsecurewithsocketwasher(J)andsocketring(K).
Installthelightbulb(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommended
wattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.